Problem calling out -Cause i = 0x80B6 - Incoming calls are barred

[manipandey]

Dear All,

I landed in some issue with making outbound call from Phones registerd to CCM. Setup is depicted below

POTS-->PBX--->GW-->CCM

GW is configured as H.323. From PBX there is a PRI lines with 50 DID coming over to one of the controller in the Gateway.

Logs is mentioned below :-

70752 is registered with CCM

calling 19173495672

###########debug isdn q931 and debug isdn error message #####

Nov 19 22:10:48.329: ISDN Se0/0/0:23 Q931: pak_private_number: Invalid type/plan

0x0 0x1 may be overriden; sw-type 13

Nov 19 22:10:48.329: ISDN Se0/0/0:23 Q931: Applying typeplan for sw-type 0xD is

0x0 0x0, Calling num 70752

Nov 19 22:10:48.329: ISDN Se0/0/0:23 Q931: Applying typeplan for sw-type 0xD is

0x0 0x0, Called num 19173495672

Nov 19 22:10:48.329: ISDN Se0/0/0:23 Q931: TX -> SETUP pd = 8 callref = 0x0089

Bearer Capability i = 0x8090A2

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98397

Exclusive, Channel 23

Calling Party Number i = 0x0081, '70752'

Plan:Unknown, Type:Unknown

Called Party Number i = 0x80, '19173495672'

Plan:Unknown, Type:Unknown

Nov 19 22:10:48.353: ISDN Se0/0/0:23 Q931: RX <- RELEASE_COMP pd = 8 callref =

0x8089

Cause i = 0x80B6 - Incoming calls are barred

Thanks in Advance

[paolo bevilacqua]

Hi,

The PBX is telling clearly that it doesn't accept this typo to call (it seems to me you expectation was that the PBX would send that to POTS). If you call a PBX extension does it work ?

In this kind of setups is generally better to have the router conencted to both PBX and telco, because the PBX can be difficult or impossible to configure for your needs.

[manipandey]

The output provided was from the GW which is the cheese between two half of Sandwich(PBX and CCM)

No, I am not able to call the extension which are part of PBX.

This is the test phase and option of connecting GW to telco is ruled out. May be input specific to some instances when someone has carried out integration with existing PBX will help .

Thanks.

[paolo bevilacqua]

Is the message the same when calling PBX extensions?

Ultimately you need the PBX configured for this work. What is it ?

[manipandey]

This is the PBX setup for PRI coming to us.

** TRUNK GROUP DEFINITION

***...TRUNK GROUP........................413

***...TRUNK GROUP TYPE...................PRI

TCI...TRUNK CLASS IDENTIFICATION.........LOCAL CO

UGP...USER GROUP NUMBER..................107

VTT...VOICE TRUNK TRANSFER ENABLED.......YES

CNC...NATIONAL CALLING PARTY # CONTENTS..NONE

DCP...DISPLAY CALLING PARTY NUMBER.......NO

PND...PRIVATE NETWORK....................NO

***...LANmark PRI TRUNK GROUP............NO

TCM...TRAVELING CLASSMARK................NO

FTH...FAILURE THRESHOLD..................3

CHT...TRUNK MONITOR MINIMUM HOLD TIME....0

DCT...DATA CALLS ALLOWED.................YES

TCH...TRUNK CALL HANDLING................EXTERNAL

NDS...DISCONNECT SUPERVISION.............YES

IGG...IGNORE GLARE.......................NO

XFT...DISTANT IBX ALLOWS FEATURE TRANSP..NO

DPT...DTMF PASSTHROUGH TIMING INDEX......NONE

RETURN CONTINUES DISPLAY..... =>

......TRUNK DIRECTION....................BOTH WAYS

*** INCOMING PARAMETERS

STY...INCOMING CALL ORIGINATION TYPE.....PRI TRUNK

TYP...INCOMING TRUNK TYPE................DIALED AND DIRECT DIAL

ICM...INCOMING CALL MESSAGE #............NONE

WPR...WHISPER MESSAGE SOURCE GROUP.......NONE

NDC...NUMBER OF DID DIGITS TO COLLECT....5

PFX...PREFIX DIGITS......................NONE

APA...TRUNK GROUP AUTHORIZATION TYPE.....NONE

PVA...PRE-VALIDATE AUTHORIZATION CODE....NO

LVL...PREDEFINED LEVEL CODE..............NONE

TNE...TONE TABLE ENTRY NUMBER............NONE

RGF...DTMF RECEIVER GROUP................52

TOO...TIMEOUT TO ATTENDANT...............NO

RAC...REUSE AUTH FOR MULT. CALLS.........NO

CWR...CALLWAIT RINGBACK..................NO

UCT...TRUNK UPDATE CDR ON TRANSFER.......ALL

CPT...CALL PROGRESSING TONES:............IBX PROVIDED

IUG...InteMail LAMP MESSAGE USER GROUPS..OWN

NUG...INTER-USER GROUP NNP USER GROUPS...OWN

NDN...NIGHT ANSWER DIRECTORY.............NONE

TCT...STATION CALL RESTRICTION ENABLED...NO

8NC...800 TO 4D SPEED NUMBER CONVERSION..NO

RETURN CONTINUES DISPLAY..... =>

NPB...NETWORK PLAYS BUSY SIGNAL FOR PRI..YES

NPR...NETWORK PLAYS REORDER FOR PRI......YES

NWT...CALL PARTY NAME WAIT TIME..........NONE

*** OUTGOING PARAMETERS

TXA...DIRECT TGRP SELECT ALLOWED.........NO

SLC...TRUNK SELECTION....................LONGEST

HDA...HARDWARE ANSWER....................YES

CXF...CANCEL TRANSFER....................NO

ICA...INTER-LATA CARRIER.................10XXX or 101XXXX

CPN...CALLING PARTY NUMBER...............SEND ALWAYS

CPM...CALLING PARTY NAME.................SEND NAME

PNN...ON-NET CALL: CALLING PARTY NUMBER..ISDN/TELEPHONY

PNF...OFF-NET CALL: CALLING PARTY NUMBER.ISDN/TELEPHONY

Thanks.

[paolo bevilacqua]

Hi,

Is that an Intecom from search:

http://www.cisco.com/univercd/cc/td/doc/product/voice/c_unity/unity30/integuid/inte_304/itinmise.pdf

the guide above is for integration with unity, you may need the pbx documentation or help from the vendor.

[manipandey]

the above guide is ther with me too but regarding Intecom pbx talking to CCM, I didn't get anything as such ..:-(

Thanks anyway for ur help and concern...