04-19-2013 06:54 AM - edited 03-16-2019 04:54 PM
Hi,
Trying to test SRST to a couple of 8961's [running sip8961.9-3-2-10] but they are stuck on "Phone Not Registering". The debug events show registration successful :-
*Apr 19 13:35:15.911: VOICE_REG_POOL: Register request for (8000351) from (192.168.2.17)
*Apr 19 13:35:15.911: VOICE_REG_POOL: Contact matches pool 1
*Apr 19 13:35:15.911: VOICE_REG_POOL: key(8000351) contact(192.168.2.17:5060) add to contact table
*Apr 19 13:35:15.911: VOICE_REG_POOL: key(8000351) exists in contact table
*Apr 19 13:35:15.911: VOICE_REG_POOL: contact(192.168.2.17) exists in contact table, ref updated
*Apr 19 13:35:15.911: VOICE_REG_POOL: key(192.168.2.17) contact(8000351) add to srst contact table
*Apr 19 13:35:15.911: VOICE_REG_POOL: key(192.168.2.17) exists in srst contact table, ref updated
*Apr 19 13:35:15.911: VOICE_REG_POOL: Created dial-peer entry of type 1
*Apr 19 13:35:15.911: VOICE_REG_POOL: Registration successful for 8000351, registration id is 6
=================================
TRU_UK_CUBE#sh sip-ua status registrar
Line destination expires(sec) contact
transport call-id
peer
---------------------------------------------------------------------------------------------------------
8000351 192.168.2.17 2066 192.168.2.17
UDP 64d814a5-2f3b10bf-763ff1ce-0680dbce@192.168.2.
40001
8000351 192.168.2.17 2145 192.168.2.17
UDP 64d814a5-2f3b10e9-784d5746-2bf3a5eb@192.168.2.
40001
8000351 192.168.2.17 2807 192.168.2.17
UDP 64d814a5-2f3b1122-6d1f6be2-5504228d@192.168.2.
40001
8000351 192.168.2.17 2886 192.168.2.17
UDP 64d814a5-2f3b114c-14142dfb-3419cb5e@192.168.2.
40001
8000351 192.168.2.17 3108 192.168.2.17
UDP 64d814a5-2f3b1176-42a4c265-3463ad6d@192.168.2.
40001
8000351 192.168.2.17 529 192.168.2.17
UDP 64d814a5-2f3b11a8-269f5b0e-113002ec@192.168.2.
40001
===================
TRU_UK_CUBE#sh voice register global
CONFIG [Version=9.1]
========================
Version 9.1
Mode is srst
Max-pool is 500
Max-dn is 500
Outbound-proxy is enabled and will use global configured value
Security Policy: DEVICE-DEFAULT
Forced Authorization Code Refer is enabled
timeout interdigit 10
network-locale[0] US (This is the default network locale for this box)
network-locale[1] US
network-locale[2] US
network-locale[3] US
network-locale[4] US
user-locale[0] US (This is the default user locale for this box)
user-locale[1] US
user-locale[2] US
user-locale[3] US
user-locale[4] US
MWI unsolicited notify is disabled
Active registrations : 7
Total SIP phones registered: 1
Total Registration Statistics
Registration requests : 7
Registration success : 7
Registration failed : 0
unRegister requests : 0
unRegister success : 0
unRegister failed : 0
Attempts to register
after last unregister : 0
Last register request time : *13:36:35.255 UTC Fri Apr 19 2013
Last unregister request time :
Register success time : *13:36:35.259 UTC Fri Apr 19 2013
Unregister success time :
========================
The important bits of the config are here ......
voice service voip
allow-connections sip to sip
no supplementary-service sip handle-replaces
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
sip
registrar server expires max 600 min 60
!
!
voice register global
max-dn 500
max-pool 500
!
voice register dn 1
number 8014141
preference 1
!
voice register dn 2
number 8000351
preference 1
!
voice register dn 3
number 8000352
preference 1
!
voice register pool 1
id network 192.168.2.0 mask 255.255.255.0
dtmf-relay rtp-nte cisco-rtp sip-notify
codec g711ulaw
sip-ua
no remote-party-id
retry invite 2
retry register 10
timers connect 100
registrar ipv4:192.168.2.254 expires 3600
sip-server ipv4:11.0.0.1
connection-reuse
=========================================
So all looks good but the handset still shows the message 'Phone Not Registered'.
Just upgraded the IOS to c3900-universalk9-mz.SPA.152-4.M3.bin
Any ideas to get these handsets to register in SRST ?
TIA
Paul.
08-03-2013 04:38 AM
hi do you still have this issue or it is solved , please let me know .
08-03-2013 09:17 AM
If you debug ccsip messages, can you see the register attemptes?
Please capture the debugs si we can see what is exactly going on.
--
Jorge Armijo
Please remember to rate helpful responses and identify helpful or correct answers.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide