01-27-2014 02:49 AM - edited 03-16-2019 09:27 PM
howdy everyone
yet another problem with my cme setup , well its acutally a feature i hope someone can point me to the right direction
(quick specs )
2821 Router 1GB mem ,128mb flash , 2GB usb 24FXO slot , and a sip trunk from vodafone with 100 numbers
i have 20+ SCCP phones and 10 faxes
i can dial out using any phone , and can dial in from my test setup
im configuring departments , like sales , purchase , accounting
basicly when someone calls the main number the telehpone has to ring on the sales department , if no one answers the purchase dept has to pickup the incomming call , if they do not answer get back to the sales group again ..
so if someone dials the main line ,all the sales phones except the manager has to ring , if no answer , the purchase phones have to ring
ephone-dn 1
number 101 secondary 0262610290 ( THIS IS A TEST NUMBER)
pickup-group 1
name PURCHASE1
preference 0 secondary 1
hold-alert 30 originator
!
!
ephone-dn 13
number 122 secondary 0869100122
pickup-group 5
name SALES1
hold-alert 30 originator
!
both groups need to able to answer the lines from one another
secondy if i call the main line and try to foward it to the sales , main line = 100 , 101 picks up purchase1, presses button transfer dials 104 purchase3
the display of purchase3 phone will read another phone instead of 101
anyone has an idea ?
Solved! Go to Solution.
01-27-2014 03:40 AM
Hi Vincent.
Under ephone-dn add pickup-call any-group so that users can press GPickUp Softkey followed by * to pickup a call from any other pickup groups.
Please refer to the following doc.
HTH
Regards
Carlo
Please rate all helpful posts
"The more you help the more you learn"
01-27-2014 05:39 AM
Hi Vincent,
the phone 1 ( 101 ) answers , asks the customer whom it might need , presses transfer button , dials 104
104 answers call from (102) which should be 101 - Your ephone-dn is not set up as dual-line.
Set up like this it will work fine.
ephone-dn 1 dual-line
Rate all the helpful post.
Thanks
Manish
01-28-2014 04:38 AM
Check by adding this
Router(config)#telephony-service
Router(config-telephony)# transfer-pattern .T
If that doesnt work send accross debug ccsip mess and debug voice ccapi inout.
Thanks
Manish
01-27-2014 03:40 AM
Hi Vincent.
Under ephone-dn add pickup-call any-group so that users can press GPickUp Softkey followed by * to pickup a call from any other pickup groups.
Please refer to the following doc.
HTH
Regards
Carlo
Please rate all helpful posts
"The more you help the more you learn"
01-27-2014 04:15 AM
Hi carlo ,
once again thanks for your quick reply .. so in essence i have to fill the ephone-dn's with "pickup-call any-group"
when i do that , any ephone-dn can pickup any group ? Example , LOGISTICS can take over a call from group SALES ?
i need to test that will get back to you on that tommorow when i have tested that
got an idea i can transfer calls ? example :
- a customer dials 111111100
the phone 1 ( 101 ) answers , asks the customer whom it might need , presses transfer button , dials 104
104 answers call from (102) which should be 101
01-27-2014 05:39 AM
Hi Vincent,
the phone 1 ( 101 ) answers , asks the customer whom it might need , presses transfer button , dials 104
104 answers call from (102) which should be 101 - Your ephone-dn is not set up as dual-line.
Set up like this it will work fine.
ephone-dn 1 dual-line
Rate all the helpful post.
Thanks
Manish
01-28-2014 03:08 AM
indeed
only i now face one problem , when i receive a call and want to transfer that to an external phone number EG more as 4 digits it doesnt work ..?
01-28-2014 03:22 AM
Hi,
Make sure that you have the dail-peers to reach the 4 digit numbers.
Thanks
01-28-2014 04:55 AM
hi , mohammed
the dailpeers i think are functioning fine , however maybe ill clarify
101 gets a call , 101 needs to consult a co-worker and dials 128 , 128 picks up the phone but has to verify with another office using an external number using a short list and dials #190, when 128 tries to dial , but gets unknown number
01-28-2014 04:38 AM
Check by adding this
Router(config)#telephony-service
Router(config-telephony)# transfer-pattern .T
If that doesnt work send accross debug ccsip mess and debug voice ccapi inout.
Thanks
Manish
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide