Hey i'm having trouble to make voip gateways (VG224) work in my network. Here is the config from the vg224 and the cme (sh ephone)
sh ephone (CME):
IP-PBX#show ephone
ephone-1 Mac:001A.E2BC.4258 TCP socket:[3] activeLine:0 REGISTERED in SCCP ver 6
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0
IP:10.1.30.110 50098 Telecaster 7940 keepalive 43097 max_line 2
button 1: dn 1 number 250 CH1 IDLE CH2 IDLE
button 2: dn 2 number 251 CH1 IDLE CH2 IDLE
ephone-2 Mac:001A.E2BC.8D3F TCP socket:[7] activeLine:0 REGISTERED in SCCP ver 6
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0
IP:10.1.30.112 50086 Telecaster 7940 keepalive 28897 max_line 2
button 1: dn 3 number 252 CH1 IDLE CH2 IDLE
button 2: dn 4 number 253 CH1 IDLE CH2 IDLE
Username: user2 Password: 202
ephone-3 Mac:001A.A29C.6D9F TCP socket:[2] activeLine:0 REGISTERED in SCCP ver 6
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0
IP:10.1.30.114 49998 Telecaster 7940 keepalive 43097 max_line 2
button 1: dn 5 number 254 CH1 IDLE CH2 IDLE
button 2: dn 6 number 255 CH1 IDLE CH2 IDLE
ephone-4 Mac:C863.EE8C.0FFF TCP socket:[12] activeLine:0 REGISTERED in SCCP ver 6
mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0
IP:10.1.30.30 38696 unknown 30032 keepalive 8558 max_line 0
Ephone 4 is for the gateway and it was registered automatically, but as you notice the type is unkown and i can't make it work even after i entered it manually.
User Access Verification
Password:
CPTC-VG224>enable
Password:
CPTC-VG224#conf t
Enter configuration commands, one per line. End with CNTL/Z.
CPTC-VG224(config)#show run
^
% Invalid input detected at '^' marker.
ip address 10.1.30.40 255.255.255.0
duplex auto
speed auto
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
ip http server
!
!
!
control-plane
!
!
voice-port 2/0
ren 3
disconnect-ack
loss-plan plan4
disc_pi_off
input gain 10
output attenuation 10
playout-delay minimum low
cptone HK
timing digit 53
description cflow1
music-threshold -50
bearer-cap Speech
station-id name CPTC
station-id number 1000
caller-id enable
!
ccm-manager config server 10.1.30.100
ccm-manager config
ccm-manager sccp local FastEthernet0/0
ccm-manager sccp
!
!
sccp local FastEthernet0/0
sccp ccm 10.1.30.100 identifier 1
sccp
!
sccp ccm group 1
bind interface FastEthernet0/0
associate ccm 1 priority 1
!
!
dial-peer vice 1 pots
service stcapp
port 2/0
forward-digits all
!
Hey guys i also tried to add ephone to the cme with mac-address ending with 401, but it's not recognizing it.
