VIC Card in 2811

[Mitchell Tuckness]

Hi,

How do I tell if my router is recognizing the VIC-2FXO-M1 card I put in it? I want to confirm the card is working, but I don't know how to tell if it is working or recognized since I purchased it used.

Thanks,

Mitch

[Leo Laohoo · Accepted solution]

The command "sh inventory" should be the first step.

[Aman Soi · Accepted solution]

Hi Mitchell,

In addition to what Mr Leo has said, u can also try show diag and also need to have Voice image .You should get the output something like Unknown Port Adaptor.

But ,I doubt the card is supported on 2800 series.

Please check the links

http://www.cisco.com/en/US/products/hw/routers/ps259/products_tech_note09186a00800e73f6.shtml

http://www.cisco.com/en/US/products/hw/routers/ps274/products_tech_note09186a00800b53c7.shtml

regds,

aman

[Nadeem Ahmed · Accepted solution]

Aman seems to be right, this module is not supported on 28XX series

Voice Hardware Compatibility Matrix (Cisco 17/26/28/36/37/38xx, VG200, Catalyst 4500/4000, Catalyst 6xxx)

http://www.cisco.com/en/US/products/hw/routers/ps259/products_tech_note09186a00800e73f6.shtml

Br,
Nadeem 

Please rate all useful post.

[Mitchell Tuckness]

I get this when I run 'sh inventory'

PID: CISCO2811         , VID: V03 , SN: FTX2341A07T

Well that sucks if it doesn't support it. I was told it would because originally it had a T1 card in it and it has 4 WVIC slots 0-3.

I also have a 2821, but it doesn't have an IOS on it yet, waiting for the memory and CF card to arrive to update it.

[Mitchell Tuckness]

I also ran 'sh diag' and I got this result:

WIC Slot 0:

        Unknown WAN daughter card

        WIC module not supported/disabled in this slot

        Hardware revision 1.0           Board revision F0

        Serial number     30276198      Part number    800-05298-01

        FRU Part Number     VIC-2FXO-M1=

        Test history      0x0           RMA number     00-00-00

        Connector type    Wan Module

        EEPROM format version 1

        EEPROM contents (hex):

          0x20: 01 2B 01 00 01 CD FA 66 50 14 B2 01 00 00 00 00

          0x30: 78 00 00 00 03 03 28 01 FF FF FF FF FF FF FF FF

[Mitchell Tuckness]

Well, is there any VOIP card that will work in the 2800 (2811 or 2821) routers?

Thanks!

[Mitchell Tuckness]

Does anyone have a suggestion for a VOIP device that is compatable with this card I can get on Ebay for relatively cheap? I see the list from this page, but it looks like some of the models need a special memory module to get as well:

http://www.cisco.com/en/US/products/hw/routers/ps274/products_tech_note09186a00800b53c7.shtml

Thanks all. I'd rather get the best item I can from the compatability list for the card, since it looks like most of them are relatively cheap, barring they don't require the additional memory DSP module.

[Aman Soi]

Hi Mitchell,

you can check your requirement from the above mentioned links.

Routers/Gateways
Model	2801	2811, 2821, 2851
Voice Network Module (right)	Not Used	NM-HD-1V 1NM-HD-2V 1	NM-HD-2VE2	NM- HDV	NM- HDV2	Chassis slot
VIC (below)
VIC-2FXO, EU	No	No	No	No	No	No
VIC-2FXO-M1/M2/M3	No	No	No	No	No	No
VIC-2FXS	No	No	No	No	No	No
VIC-2E/M	No	No	No	No	No	No
VIC-2BRI-S/T-TE	No	No	No	No	No	No
VIC-2BRI-NT/TE	No	No	No	No	No	No
VIC-2DID	Yes	Yes	Yes	No	Yes	Yes
VIC-2CAMA	No	No	No	No	No	No
VIC-1J1	No	No	No	Yes	Yes	No
VIC-4FXO-M1	No	No	No	No	No	No
VIC-4FXS/DID	Yes	Yes3	Yes3	No	Yes3	Yes3
VIC2-4FXO (FXO/CAMA)	Yes	Yes	Yes	No	Yes	Yes
VIC2-2FXO (FXO/CAMA)	Yes	Yes	Yes	No	Yes	Yes
VIC2-2FXS	Yes	Yes	Yes	No	Yes	Yes
VIC2-2E/M	Yes	Yes	Yes	No	Yes	Yes
VIC2-2BRI- NT/TE	Yes	Yes	Yes	No	Yes	Yes
VWIC-xMFT-E1 (with or without DI)	Yes	No	Yes	Yes	Yes	Yes
VWIC-1MFT-G703	Yes	No	No	No	Yes	Yes
VWIC-2MFT-G703	Yes	No	No	Yes	Yes	Yes
VWIC-xMFT-T1 (with or without DI)	Yes	No	Yes	Yes	Yes	Yes

as far as Memory and Flash is concerned, install ipvoice image with yor existing DRAM/Flash & check.

regds,

aman