cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1457
Views
0
Helpful
1
Replies

IPV6 multicast ping not working

sachin30720041
Level 1
Level 1

Hello,

I am configuring ipv6 multicast in the below-shown setup. ospfv3 and PIM sparse-mode is enabled on all the routers and on all the interfaces of the router.

R1-----R2------(gi0/1)R3

  \                                 (gi0/0)

    \                                 |

      \                               |

           R6                      R4

               \                     |

                   \                |

                           R5

 

R3 is the RP. R6 joins FF08::1 multicast group and mroute entries are created from R6->R1->R2->R3.  

 

If the outgoing interface is gi0/1(interface pointing to R2) then ping works from R3.

R3#ping FF08::1 source lo0
Output Interface: Gigabitethernet0/1======>Gigabitethernet0/1 points to R2

Reply to request 0 received from 6::6, 359 ms

But If I ping from router R3 but give the output interface Gigabitethernet0/0(pointing to R4) then ping does not work. Why?


R3#ping FF08::1 source lo0
Output Interface: Gigabitethernet0/0

Request 0 timed out

 

Below is the configuration of all the routers.

iosr1
-------------------------------
ipv6 unicast-routing
ipv6 multicast-routing
ip multicast-routing


int gi0/0
ipv6 enable
ip address 100.10.20.1 255.255.255.0
ipv6 address 2001:face:12::1/64
no sh
ospfv3 1 ipv6 area 0
ip pim sparse-dense-mode

int gi0/1
ipv6 enable
ip address 100.10.60.1 255.255.255.0
ipv6 address 2001:face:16::1/64
no sh
ospfv3 1 ipv6 area 0
ip pim sparse-dense-mode

int lo0
ipv6 enable
ip address 1.1.1.1 255.255.255.255
ipv6 address 1::1/128
ospfv3 1 ipv6 area 0
ip pim sparse-dense-mode

router ospfv3 1
router-id 1.1.1.1


iosr2
-------------------------------
ip multicast-routing
ipv6 unicast-routing
ipv6 multicast-routing

int gi0/0
ipv6 enable
ip address 100.10.20.2 255.255.255.0
ipv6 address 2001:face:12::2/64
no sh
ospfv3 1 ipv6 area 0
ip pim sparse-dense-mode

int gi0/1
ipv6 enable
ip address 100.20.30.2 255.255.255.0
ipv6 address 2001:face:23::2/64
no sh
ospfv3 1 ipv6 area 0
ip pim sparse-dense-mode

router ospfv3 1
router-id 2.2.2.2

int lo0
ipv6 enable
ip address 2.2.2.2 255.255.255.255
ipv6 address 2::2/128
ospfv3 1 ipv6 area 0
ip pim sparse-dense-mode

iosr3
-------------------------------
ip multicast-routing
ipv6 unicast-routing
ipv6 multicast-routing

int gi0/0
ipv6 enable
ip address 100.30.40.3 255.255.255.0
ipv6 address 2001:face:34::3/64
no sh
ospfv3 1 ipv6 area 0
ip pim sparse-dense-mode

int gi0/1
ipv6 enable
ip address 100.20.30.3 255.255.255.0
ipv6 address 2001:face:23::3/64
no sh
ospfv3 1 ipv6 area 0
ip pim sparse-dense-mode

router ospfv3 1
router-id 3.3.3.3

int lo0
ipv6 enable
ip address 3.3.3.3 255.255.255.255
ipv6 address 3::3/128
ospfv3 1 ipv6 area 0
ip pim sparse-dense-mode

iosr4
-------------------------------
ip multicast-routing
ipv6 unicast-routing
ipv6 multicast-routing

int gi0/0
ipv6 enable
ip address 100.30.40.4 255.255.255.0
ipv6 address 2001:face:34::4/64
no sh
ospfv3 1 ipv6 area 0
ip pim sparse-dense-mode

int gi0/1
ipv6 enable
ip address 100.40.50.4 255.255.255.0
ipv6 address 2001:face:45::4/64
no sh
ospfv3 1 ipv6 area 0
ip pim sparse-dense-mode

router ospfv3 1
router-id 4.4.4.4

int lo0
ipv6 enable
ip address 4.4.4.4 255.255.255.255
ipv6 address 4::4/128
ospfv3 1 ipv6 area 0
ip pim sparse-dense-mode

iosr5
-------------------------------
ip multicast-routing
ipv6 unicast-routing
ipv6 multicast-routing

int gi0/1
ipv6 enable
ip address 100.40.50.5 255.255.255.0
ipv6 address 2001:face:45::5/64
no sh
ospfv3 1 ipv6 area 0
ip pim sparse-dense-mode

int gi0/0
ipv6 enable
ip address 100.50.60.5 255.255.255.0
ipv6 address 2001:face:56::5/64
no sh
ospfv3 1 ipv6 area 0
ip pim sparse-dense-mode

int lo0
ipv6 enable
ip address 5.5.5.5 255.255.255.255
ipv6 address 5::5/128
ospfv3 1 ipv6 area 0
ip pim sparse-dense-mode

router ospfv3 1
router-id 5.5.5.5

ios6
-----------
ip multicast-routing
ipv6 unicast-routing
ipv6 multicast-routing

int gi0/1
ipv6 enable
ip address 100.10.60.6 255.255.255.0
ipv6 address 2001:face:16::6/64
no sh
ospfv3 1 ipv6 area 0
ip pim sparse-dense-mode

router ospfv3 1
router-id 6.6.6.6

int gi0/0
ipv6 enable
ip address 100.50.60.6 255.255.255.0
ipv6 address 2001:face:56::6/64
no sh
ip ospf 1 area 0
ip pim sparse-dense-mode

int lo0
ipv6 enable
ip address 6.6.6.6 255.255.255.255
ipv6 address 6::6/128
ospfv3 1 ipv6 area 0
ip pim sparse-dense-mode
ipv6 mld join-group FF08::1
 
----------
 

 

1 Reply 1

Harold Ritter
Cisco Employee
Cisco Employee

Hi @sachin30720041 ,

 

You need to configure the RP address on all devices using the following command, including on the RP itself.

 

ipv6 pim rp-address <RP ipv6 loopback interface address>

 

Regards, 

Harold Ritter
Sr Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México
Paseo de la Reforma 222
Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: