I am runing ACS 4.2 on Windows 2003 and for some reasons I need to rename the server name? Is it going to create any issues?
I am runing ACS 4.2 on Windows 2003 and for some reasons I need to rename the server name? Is it going to create any issues?
I am getting ready to install a new ACS 5.1 server to replace my current 4.1 acs box. I wanted to start off with a fresh install rather than upgrading all of my 4.1 data.Can I have devices (ASA for VPN authentication, routers & switches for user auth...
Hi Gurus,I have deployed a Cisco wireless environment at one of our sites. The problem is that we are rolling out new motorola handhelds (MC75) are not authenticating with the ACS. I have copied the same config as it was with the exsisting wireless ...
HI,I am setting up Radius AAA for cat6K switch.For authentication its work and user can login to switch. But for the privilege level assignment, it does not work. After loging in, I always get privilege 1.I need your guide on how to configure on ACS ...
Folks,I have an issue with an implementation, I had a ACS R5.1 that I'm using to authenticate the wireless users with 802.1x, that's OK and working fine. Now I want to use the same ACS to authenticate wired users using MAB (for IP phones, printers, s...
Hi, I m using ACS for Authentication, Authorization and Accounting. I dont want accounting for SHOW commands. Can any one suggest the requisite commands to be configured on cisco router or switch so that SHOW commands will not be accounted?
Hi at alli have a Problem with the cisco-av-pair string on the Cisco ACS and a SSID.We have here some SSID and some AD Groups. It was no Problem with the old Cisco ACS 4.2. I have here configured the string: cisco-av-pair ssid=myssid. The Clients ...
Hi,Need help with Cisco Secure ACS 4.0
I cannot get login working via TACACS from my Nexus 5548. I've tried creating a group and a single server with key etc.Config is simple:tacacs-server key 7 ************ip tacacs source-interface Vlanxaaa group server tacacs+ tacacs server 10.x.y...
Hello MembersI am running ACS 5.1 (on VMware platform), just stouck up with the requirement mentioned below.Existing Setup # Wireless guest users at present are authenticated against ACS 5.1 local database, client wants they should be time based, for...
Hello,I am trying to determine how I can assign a static IP to a user in ACS 5.2. I am able to do it in ACS 4.2, but I don't see the same options under 5.2.General idea is that users authenticate from our VPN appliance via RADIUS, and upon authentica...
Using AAA on a PIX, authentication works fine and the AAA user has full rights over PIX, but aaa authorization always fails when going into conf t
Just upgraded from 4.0 - to 4.2 then to 4.2.1 15. As you may have seen with periovous posts of mine its not been an esay ride.I have now managed to get it all working - backups AAA etc but for some reason i cannot get the replication to work! Its sta...
Good morning my fellow Cisco users! I have Dot1x set up (with certificates) and running to the point that im almost ready to put it into my production network! I have one thing im trying to work out that I hope is doable. On my test port I haveswit...
HiI'm trying to configure ACS 5.2 so that should it loose connectivity to Active Directory it chooses the local authentication, however I can't seem to make this work.Within ACS 5.2, Access-Policies, Access Services, Default Device Admin, Identity,I ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-18-2026 02:37 PM | ||
| 04-27-2026 04:44 PM | ||
| 04-22-2026 01:25 PM | ||
| 03-05-2026 07:50 AM | ||
| 02-18-2026 03:44 PM |
| User | Count |
|---|---|
| 1 | |
| 1 | |
| 1 | |
| 1 | |
| 1 |