Resolved! Port Forwarding
How to make a port forwarding for my network? My public ip 202.186.57.121 and private ip 192.168.1.1I wants to open port to allow outside can access my network too.
This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other troubleshooting best practices.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other troubleshooting best practices.
Forum Posts
Hi,Currently I am integrating ISE(software version: v2.7, patch 5) with Fortinet switch. And my endpoint which is connected to the switch has been authenticated from ISE successfully, just like the snapshot below. However, in Live Sessions, "IP Addre...
Resolved! Checkpoint pxGrid Integration
Hi Folks,Do we have any guides on integrating Checkpoint with pxGrid for identity awareness?Thanks
Hi Experts,Is configuring mac binding and 802.1x together a good idea?Has anyone done this kind of deployment earlier? Any side effects if these both are working together on the switch?Also, can this be configured for Wireless network?Also what are t...
Hi all,we are testing ISE with our non-switches and everything is going smoothly except CoA. We are doing EAP-TLS machine auth with AD and using anyconnect.Machine is authenticated with username "XYZ" (confirmed by packet capture), the switch is gett...
Hi Experts,Just wanted to know what information is backed up in the operations data on ISE?Can this be used to extract reports for more than 90 days...?Report including posture by endpoint or posture by posture policy?
Resolved! MAB for Printers - AuthZ failed - Wired
Dear community, I connected the Printer to the switch port, ISE reads its MAC via Probing. I assigned a static group that I created named "Printers" to that MAC, and created a rule with AuthC(if MAB) and AuthZ(if MAB and if part of the Printers stat...
Sometimes after rebooting device connected to 801.x port this device successfully perfoming 802.1x authenticationOct 19 13:29:27.869 MSK: %LINK-3-UPDOWN: Interface GigabitEthernet3/0/23, changed state to down Oct 19 13:29:28.980 MSK: %AUTHMGR-5-START...
Resolved! 802.1X - multi server radius ??
Hi everyone,i'm working on project to deploy 802.1X security on all my L2 switches on our HQ. this part is the first step but we plan to deploy this security on all L2 switches of remote site (Branch office, shop, warehouse..)- we are using NPS from ...
Resolved! Install ISE on bare metal
Hi,simple question. Is it possible/supported to install ISE on a bare metal server? HP, DELL, etc.thank you
Hi Experts,Setup:ISE 2.7 with switch running IOS 15.xPosture checks with VLAN change from limited access to full access for compliant endpointsIP device tracking commands are enabled on switchIssue:ISE live logs show different IP address compared to ...
Hi, I'm running an installation of Cisco ISE 2.7 patch4, (which, is documented to fix CSCvv14390 - Concurrent sessions not working). The limiting of concurrent session now works, which is fine.However, I'm noticing that on the next attempted session ...
Good morning, we have a problem to Guest Portal Redirect.When the guest user arrive on Guest Portal, he receive the error (see the first attachment error1.jpg)We have a Anchor-Foreign architecture, the ACL that we use is the second attachment named a...
Hi guys, What are your experience with using radius load-balancing feature in Cisco IOS, specifically on 2960x switches (15.x versions).I am speaking about command "load-balance method least-outstanding" under radius server group. Are there any probl...
Resolved! Policy set flow and use option
I do not clearly the flow of policy set and the behavior of continue option. 1. The behavior of continue option.After the process of getting the allowed protocol, the next step is authentication.In the case that Wired_Dot1x condition is selected as c...
