Hello, I Would like create the script for add the device (PC with Mac address and description). is it possible to create it with powerhsell? Or Python ? If both works, which is the most appropriate? Thx for your help guys !
This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other troubleshooting best practices.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other troubleshooting best practices.
Forum Posts
Hi Team, I wanted to confirm if mix/match standalone with distributed deployment is supported. For example is a following 3 node installation supported: Node 1: PAN (P) + MnT (S) + pxGrid + PSN Node 2: PAN (S) + MnT (P) + pxGrid + PSN Node 3: PSN ...
Resolved! SNS-3655 support 100,000 NADs for TACACs
Hi, please, can you help me to clarify if the SNS-3655 only to support TACACs can support 100,000 NADs or the number of NADs is limited to end points that is 25,000 in standalone mode? Thanks, Joao Cardana
Hello, I have configured ISE 2.4 to create wifi hotspots and self registration access. We user a WLC 2504 controller software version 8.5. Everything works fine with windows devices and android devices which get correctly redirected to ISE portal pag...
Resolved! ISE clean unnecessary endpoints
In endpoints list I see a lot of devices which I don't need to be managed by ISE such as IP phones. Even MAC addresses that coming from telecom providers are listed there. Those devices are not even in our network! Devices takes licenses, why should ...
Resolved! ISE TACACS licensing question
For TACACS license, in the license ordering guide it says that "One ISE Device Administration license is required per Policy Service Node that operates on Device Administration transactions". If I have 2 PSN's that means I will need to purchase 2 x L...
Resolved! ISE and public certs for EAP
Hi All Our current ISE node is registered as ise.xxx.localIs it possible to use ise.xxx.com as the EAP certificate? I presently have the .com wildcard cert used for guest and sponsor portal but I don't think it is setup correctly for EAP. So I want...
Hi,Can I say tht this device nvr authenticated via dot1x and mab? Therefore if continue for few months or so, the device is inactive and can be removed from the customized identity group? FailureReason: 22056 Subject not found in the applicable ident...
Hi All, In one of the requirements, we would like to restrict personal devices to access corporate networks over 802.1x wired or wireless using MSCHAP. We can add machine authentication on top of it. Can I simply use EAP-TLS to eliminate machine au...
Hi Folks, I am running a POC using ISE 2.4 latest patch with Stealthwatch 7.1 patched with patches 1 and 2. I am seeing a Green good connection in Stealthwatch, but in ISE it is showing offline. Certificates are set for auto approval. The log in pxg...
Resolved! Non 802.1x switches & Cisco ISE
Dear All, We have a mixed environment of cisco switches and non-cisco (Does not support 802.1x). There is less very feasibility to replace non-cisco switches and need to configure 802.1x and posture services for laptops. what can be the best solutio...
Hi community, i want to authC and authZ Rittal CMC devices with ISE 2.3. I think the radius process is not the problem for me. I don't know how to add this device into ISE dictionaries with the appropriate attributes. I'am searching for a solution ...
I appear to be running into bug CSCuz96643 but the bug says it's fixed in 2.6(0.156) which is what I'm running. How can I figure out what is causing this? Thanks
I am being flooded with "Supplicant stopped responding" alarms via emails.However, i would like the alarm enabled and sent to syslog but not sent via emails. Removing the email address under "alarm notification" will remove the email address from all...
Hi, Are using HP Thin Clients with Windows Embeded. At the moment we are trying authentication on switch ports. The thin clients are being authenticated with MAB.We have run in to an anoying issue where the client asks for DHCP and displays an error ...
