Hello,Is there a way to find out more information regarding the migration tool output from the Policy Gap reports.I have a migration report which outputs "Description: RADIUS attribute not found in the cache." for several SSPs in ACS. A specific Attr...
This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other best practices.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other best practices.
Forum Posts
We're using radius, asa 9.6.x and windows 2012 nps. Our client is asking if there is any way to prove what authentication protocol is being used for anyconnect clients. I understand that PAP is being used by default and MSCHAPV2 is default when pass...
Hi,ISE Virtual Appliance Supports VMWare ESXi as Hypervisor. Is there any Plan on the roadmap that ISE will be supported on HyperV (or possibly XEN) in the future, because some customers don't have VMWare but using only HyperV. The same question may ...
ISE 2.3p1(post 10-18-2017 update) VM, running on HyperV 2012R2I know the wireless wizard is beta.But it doesn't matter so far what wireless wizard I try to run, they all get to the "Wireless LAN Controller" screen...and just sits there spinning at 'l...
Hi experts, Quick question about guest portals on ISE for wifi onboarding. Is it possible to have different personalized guest portal for different locations ? In this case all locations will share the same ISE deployment.
Hi board,my CiscoNotification eMail alert told me, that a new BIOS is available for the SNS 35XX hardware appliances.Until now, the appliances were shipped with CIMC 2.0(9c) with the hint, that that should not be changed (unless advised by TAC).So no...
Hi,We have an issue with our deployment of mab...We use the global and interface specific configuration below.3.1. Global commandsaaa new-modelaaa authentication dot1x default group radiusaaa authorization network default group radius aaa accounting ...
Resolved! ISE Device Admin and Base license count
Hi board,I understand, that base licenses are required on the ISE, before a device admin (TACACS+) license can be applied.The documentation states, that 100 base licenses are required (I guess because this is the lowest available base license count)....
Resolved! NEAT x BPDUGuard
We are testing NEAT to provide network to some meeting rooms. BPDUGuard is globally enabled on authenticator switches. When supplicant switch is connected to a port, before the authentication completes, port is put in err-disable. If bpduguard is dis...
I've read that ISE REST API uses TLS (https) over port 9060 with basic authentication. Is there any additional encryption being done for the username and/or password other than sending the data thru the TLS tunnel? e.g. password encrypted with public...
Hi All I found the acl not work before my device during running auth below is the ACL interface command AAA command Would you have any suggest for me? Thanks!
Resolved! ACS and DNAC integration
Hi,Is there any documentation for ACS and DNAC integrationThanks
Resolved! Time-based Radius CoA dynamic trigger
Hi,How do I achieve the below use cases with ISE and Wireless?Only allow access to the network from 9am – 6pm, and disconnect any “active” clients after 6pm?Assign a Radius av-pair AIrespace-QoS-Level to clients who authenticate from 9am-6pm, but as...
Hi All, Can we perform mac based authentication on ISE ? I am doing the same on WLC but have reached the maximum limit. Is there a way to do the same on ISE 2.3 ? If Yes, then how ?
To support wired/wireless BYOD for Windows and Macs, are admin rights needed for the logged in user on the local machine to accept the configuration changes in the wired/wireless profiles distributed by Native Supplicant Profile? I've looked in ISE ...
