02-22-2011 07:46 AM
I have the same problem as the following post:
https://supportforums.cisco.com/thread/176673?tstart=0&viewcondensed
Also, LMS fails inventory collection every time. I click on the "failed" link from LMS Portal, but the page never comes up detailing why it has failed. This is after I fixed an issue with group policy overwriting the "Logon as batch" setting for casuser. Everything appeared to be up and running normally again, when I noticed the next day that inventory polling/collection is failing. pdshow attatched.
The following error message continues to show up in the rme_ctm.log file:
[ Tue Feb 22 07:40:55 CST 2011 ] URN_NOT_FOUND : urn "JRM" : Not found !!
The last entry in the CTMJrmServer.log file is:
[ Thu Feb 10 10:52:55 CST 2011 ],INFO ,[main],com.cisco.nm.rmeng.jrmwrapper.server.CTMJobManagerServer,publishDaemonOk,99,Called CreateReady file. Return Value 0
I've been blindly trying to chase this down and getting nowhere.
Solved! Go to Solution.
02-22-2011 07:51 AM
Hi,
Please remove ctmregistry and ctmregistry.backup from CSCOpx/MDC/tomcat/webapps/rme/WEB-INF/lib, restart daemon manager with the following command :-
net stop crmdmgtd --> to stop daemon
net start crmdmgtd --> to start daemon
While applying this workaround make sure to stop "Windows Remote Management" service of CiscoWorks server. You can access this from Start > run > services.msc.
Try this one more time and if the issue pressist then send me the output of pdshow , jrm.log and CTMJrmServer.log ..
Thanks--
Afroj
02-22-2011 07:51 AM
Hi,
Please remove ctmregistry and ctmregistry.backup from CSCOpx/MDC/tomcat/webapps/rme/WEB-INF/lib, restart daemon manager with the following command :-
net stop crmdmgtd --> to stop daemon
net start crmdmgtd --> to start daemon
While applying this workaround make sure to stop "Windows Remote Management" service of CiscoWorks server. You can access this from Start > run > services.msc.
Try this one more time and if the issue pressist then send me the output of pdshow , jrm.log and CTMJrmServer.log ..
Thanks--
Afroj
02-22-2011 08:59 AM
Thanks, that did the trick!
Now, if you can only explain what this did, or why this was the correct course of action.
02-22-2011 09:47 AM
Hi ,
Great ..
The issue was this Port was blocked 47001, which was blocked . what we did will skip that Port and the ctmregistry should have EssentialsDM on a new port, and the conflict should not reoccur.
Thanks--
Afroj
02-22-2011 10:17 AM
Thanks for the explanation!
02-22-2011 12:44 PM
02-22-2011 11:42 PM
Hi ,
I checked the Pdshow every other process is running as Expected , also I checked the the log file and No error in it.
com.cisco.nm.rmeng.jrmwrapper.server.JobManagerExt,getJRM,383,getJRM: SUCCESSFUL CONNECTION TO JRM.
Please attached the screen shot of the Error ..
Thanks--
Afroj
02-23-2011 04:51 AM
One example is when trying to schedule a config sync, I get the following:
DCMA0055: URN_NOT_FOUND : urn "JRM" : Not found !!
DCMA0077: Could not create job. Check dcmaclient.log for more details.
However, I delete the ctmreg files and restart services and everything works fine. I would like to prevent this from reocurring after each reboot. Is there any other information/logs that might be useful?
02-23-2011 05:41 AM
Hi ,
The reason must be some 3rd Party application Installed on the Same server , which is using the same Port which is supposed to be used by cisco works!!!
Check the below link for Ports used by cisco works :
http://www.cisco.com/en/US/products/sw/cscowork/ps4737/products_tech_note09186a00800e2d78.shtml
Thanks--
Afroj
02-23-2011 07:57 AM
I've decided to leave WinRM service as manual. After reboot, LMS is fully functional and runs with no errors. If this service being set to manual causes me problems in the future, I will update this discussion. Thanks for your assistance.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide