Hi, I have upgraded to ASA9-14-4-24-smp-k8 and it was successful.I also have to upgrade the asdm module, I have a asdm-7202 and asdm-openjre-7202.Question, do I need the openjre file ...? if so, do I need to point it someone or just drop it in flash:...
Forum Posts
I got alerts from my Firepower this morning for this. The source IP is my DNS server, and the destination was my DNS provider. I can't find anything in the alert that I can use to locate the system that actually issued the request to my DNS server. I...
Hi Team , i need remove weaker encryption algorithms on a Cisco 3750. I have switch WS-C3750-48P, SW Version 12.2(55)SE11, Image c3750-ipbasek9-mz.122-55.SE11, k9 Version. The command that I' m going to apply are ip ssh dh min size 4096 ip ssh s...
Hi All,we have run tenable scan and we have Vulnerability in Cisco switch Catalyst 3850 48 Port PoE and we find the some vulnerability given below.1.Cisco IOS XE Software Command Authorization Bypass (cisco-sa-aaascp-Tyj4fEJm)2.Telnet Vulnerability A...
Now upgraded to FTDv100 on VMWare to 7.4.2, got the following issues: Unlike in 7.3.2, which suddenly stopped all the traffic on interfaces, now on 7.4.2: - suddenly HostScan stopped working properly, stuck on "HostScan mission complete" and not mov...
Hello All,In my company we have run tenable scan and we have Vulnerability in Cisco switch Catalyst 3850 48 Port PoE SNMP Agent Default Community Name (public)Can you help to fix this issue ? Can any one help in this issue.
I have lately realised that there is no way to actually figure out the physical interfaces used by a port-channel in FTD 4110s or 2120s or probably any FTDs through the FMC gui or FTD cli. I asked TAC about this and they also advise there is no way t...
Resolved! ASA Same Security-Level 100
HiWe are moving from an EVPL to SDWAN, and for that I needed to configure another interface on the ASA (it currently has a 0-security level). What I would like to do is to have the two interfaces (inside and SDWAN) have the same security level of 10...
my company has the firepower 1120. when i want upfate, maualy or scheduled, geolocation, vdb, intrusion rule, i receive error like on picture i noticed on my device dri-firepower# show timezoneTimezone: UTCdri-firepower# show clockThu Aug 15 06:42:08...
Hi,if I try to enter module 1 via telnet, I get the error message: # connect module 1 telnet Type exit or Ctrl-] followed by . to quit. error reading input file # It's only possible to enter it with console: # connect module 1 console Telnet escap...
Hi!We deployed FTDv100 7.3.1.2 (Build 79) on VMWare ESXi 7.0, and we experience now the following problem:- SUDDENLY inside and outside interface stop passing ANY traffic, including ARP!!! Meanwhile management interface is working! Debug is absolutel...
Resolved! FTD not registering to FMC
FTD: 3130FMC: 1700FMC on-net and in HA with databases synchonised. Time set correctly. FTD management interface is on the same subnet as FMC. Only interface connected is management interface. FTD can ping FMC and FMC can ping FTD.Try to add FTD as a...
Hi All,My task is to replace existing mx device with 1120 and connect to the MS350 upstream, which is cloud managed and requires access via VLAN1. 1120 ia managed via Cisco FMC. Giving that, I am unable to implement VLAN 1, which is necessary for Mer...
FMC Version 7.2.5.1AD Integration failing when switched from LDAP to LDAPS with general error - check user/password/connectivity. AD Server is in the same network, accepting LDAPS from any source, user/password was double-checked, AD Root-CA certific...
Resolved! FMC FTD HA Cluster
Hello community,currently we are facing a challenge to build FTD HA cluster using FMC while using the same interface for DATA and MANAGEMENT traffic processing.However it turned out that on FTD models 1150 such setup is not supported. When building u...
