Anyone had any luck getting the Firepower virtual appliance for VMware (vFTD) running in workstation? I have tried it on 12.0 and 12.5 but upon initializing it blows up with a stack dump. I've seen others say the error is related to initializing the ...
Forum Posts
Hi, i'm planning to add Firepower module to ASA 5515-X/K9 & i need to know what are the required components to make it work? Also i need to know if Firesight Management VM or appliance is required for managing the FPWR module or is it manageable by ...
Hi there i have a quick question regarding the Firepower User Agent. I have read in the documentation that if you require to monitor more than 5 AD servers you are required to install another User Agent. However i was attending Melbourne Cisco Live r...
Resolved! ASDM access troubleshooting
I am trying to get into the ASA to check some settings and it is giving me the error of "Unable to Launch Device Manager" I was in on Thursday with the same credentials so I am not sure what is going on. Also, we need the ASDM client so that we can l...
Hello All, One of our company's firewalls has a "permit any any" rule and I've been tasked with auditing the connections. The goal is to get rid of the permit any any but I'm not sure what will be the best way to do this. We have 4k+ live connect...
Dears, I have a query related to URL filtering, we have enabled a youtube for specific users and these were working fine,, in my other rule ( internet website allowed) I found the uncategorized category is also allowed which is not a good practice s...
Dears, Currently I m having a site to site vpn with pre-shared keys , I want to move to digital certificate authentication by a (globalsign or verisign or godaddy) , can anybody route me to the step by step configuration for ikev2 with certificate au...
Hello Cisco Community. I have a problem with power on my Primary cisco ASA. Secondary ASA has bacame an Active state. I need to replace my Primary ASA to new hardware with the same model. Will there be an interruption to network traffic if i change m...
Cisco 2851 w/NME-IPS-K9 Module - The IPS Module has an IP Address of 192.168.1.2 (Management port) - A seperate NIC in my PC has an IP Address of 192.168.1.1 - I can communicate with the IPS Module with no problems - The Cisco Router has an IP Ad...
I'm replacing my 5516 ASA's due to the forced RMA. Anyways, I'm in an active/standby configuration. I replaced the secondary and failed over to test, all is good and I'm running on it. So the state I'm in is Primary/standby and Secondary/Active. No...
Hello, I built a rule that allows server 1.1.1.1(source) access to server 2.2.2.2(destination) on port 8400 and I tested the rule to make sure it works. I understand that firewalls are statefull and should agree on both directions, but lets say that...
Hi recently i deployed FTD 2140 in HA. i created multiple sub-interfaces on FTD for inter-vlan routing. i am facing one issue regarding Ping between host in different VLANs and i am not able to ping between hosts in different VLANs. 1- ICMP in...
Hello guys, I need help with this issue, I have an ASA 5585 X with a module SSP-40 already installed. and the idea is to activate it (SSP-40 for firepower services) and additionally add the licenses AVC, AMP, filter URL, and IPS, I need to know if I...
I am looking at creating baselines for our FirePOWER sensors (i.e. CPU, traffic rates, etc...) Is there a good way/built in functionality to collect/export this data - other than through a full-blown NMS solution utilizing SNMP? I would like to s...
Hi, how can I send Syslog messeages of Access Control Rule to an external Syslog Server? I need to see which connections are Blocked or Allowed for specific Rules. In logging settings for Access Controll Rule I can configure Syslog Alert but I don...
