Hi there, I am new to Cisco but recently got a Cisco RV340 Dual WAN Gigabit VPN Router for the purpose of using its S2S functionality to establish a connection to Azure Cloud. The Router is behind another edge NAT with port forwarding to udp ports...
Forum Posts
Resolved! Readiness check stuck
Hi all, I am doing the third upgrade to 6.2.2 version (two upgrades were done without errors) and when I run the readiness check my browser crashed. After reopening the browser the process was stuck. I did not check it and I tried to start it again....
Hi There, i have cisco 5516-x with FP module and FPMC installed on VM (6.0.1). i have added license and enabled them for device. also i have added service policy rules in ASA 5516 with enabling firepower inspection. but still i am not able to do URL ...
I have setup a CallHome feature on a UCS through the GUI. I've followed it step by step in accordance to the instruction that I pulled from Cisco.com. However, I am not receiving the alerts or even when I click on the send inventory button. If I go i...
I have a new set of Firepower 2130 appliances and a Management Center 1000. One of the differences between the 5525x and the Firepower is that some users can run traceroute, tracert or mtr and get useful information. Other users cannot get past their...
Hello Experts, I need your help with a configuration bit for Object based NAT - Natting two public IP to one private IP. I am asked to nat two public IP to one private IP 8.xxx.xx.90 and 8.xxx.xx.92 to nat to 10.53.19.8. 8.xxx.xx.92 nats to 10.5...
Hello, This could be due to pure ignorance on my part, but I noticed odd behavior on one of the ASA's I manage. There were a couple clients showing as the source IP for a SYN Attack. Of course, I jumped to malware and scanned the heck out of one ...
It is to my understanding that there are only specification differences between the two models listed in the title. If I wanted to restore a backup from a 4140 to a 4120 appliance, then will I run into any problems? Is this possible in the first pl...
Can I do a direct software upgrade from 9.1(4) to 9.1(7)23?
Dears. I am following the below link for creating the self signed certificate for captive portal but when I try to generate CSR I get an error as attached. Also I tried with link 2 but no luck captive portal self signed certificate https://www.cisc...
Resolved! ASA 5525-X Firepower Services upgrade
Dears, I am planning to upgrade the Defense center and the sensor, I have seen the upgrade path to 6.1.0 from current version 6.0.1 , I have only one doubt do I have to upgrade the boot images and the packages also to 6.1.0 or they can remain on 5.4....
We are thinking of spinning up a second VM, one in each DC and we split the existing load between the two. This will give us an upper limit of 50 appliances and some redundancy with regard to potential outages. We would need to do further research to...
Hi, I have two ACS appliances running 5.7.0.15.2. Appliance 1 has policies on, appliance 2 is to be the secondary appliance. I've been trying to add the secondary to the primary for replication and the secondary appliance does not seem to be be...
Resolved! FTD Firepower Policy
Hi Team! I am having some "trouble/issue" with setting a Policy in the FMCv. I have manage to create a Malware policy to block Malware (Block with reset), Ok that works fine. But at the same time when I am downloading the same Malware with HTTPS/SS...
Hi, I am having issues downloading the 8.2.5 ED and 8.4.5 ED versions of the Adaptive Security Appliance Software. I get an error message that there is no server response. I was able to download 8.3.1 successfully. Is there a reason why these files ...
