HelloI upgraded the OS on our ASA 5505 from asa917-9-k8.bin to as917-16-k8.bin to mitigate the 200 day bug. All but one ASA upgraded nicely and can be reached by ASDM. This ASA upgraded but I can't connect to it in ASDM. It is the only device with mu...
Hi, It's been a few days that I'm trying to figure this out and I didn't find why my NAT is not working. ( ICMP Packets dropped by NAT rule, no internet connection even though the firewall is WIDE OPEN). I try to get a dynamic NAT with the outside Vl...
All,I'm fairly familar at this junction with Firepower and FMC. Installed it and have been using it for approximately 8 months now on 5512x and 5525x ASAs but by my own admission my knowledge has a long ways to go. I have been asked to assemble a B...
Since I upgraded my ASA devices to 9.8(1) I get a new popup when I login to the devices "Login History is not available for the logged in user." is there a way to:1) enable Login History or2) disable the popup. I've looked around for documentation ab...
Hello, So I'm what I'd call... "fairly new" to firewalling. I've got two sites that have a site to site tunnel (technically 3, but we'll get to that later), that have issues. I have a total of 12+ sites. All of them connect through a site to site tu...
Hi there!I've a simple scenario:1. Firewall ASA 5510 that connects to internet to Fa0/02. Layer 3 switch that is connected to Fa0/1 to ASA5510, and have some vlans for users.Now, I want to implement DMZ zone to firewall, to publish one of the server ...
Hi, I have an ASA5512X and experiencing an issue with connectivity. Basic network layout is - Inside-Gi0/1 - - - Mail Server A (local IP 192.1.1.1) | ...
Hi all can we configure and deploy firepower 2140 as ngips only in HA mode .If possible please suggest how?
Has anyone ever seen this problem where the ASDM looks to be like you are on one firewall but you are actually in another firewall? When I open the ASDM using the standby IP it shows that I'm on the standby ASA. The IP address on the deice list for...
Greetings all: So last night I had an issue joining some new firepower sensors to our FMC also running 6.2.2. I replaced the IDS cards in a Cisco 5585 ASA (running 9.8 (2)) and the install process ran smoothly. This is the 3rd pair of Firepower IDS c...
Hello, A third party security threat has flagged off the below threat on our cisco router "Remote Management Service Accepting Unencrypted Credentials DetectedHTTP Security Header Not Detected" Even though i do not see any FTP service running on the ...
Hello Team, Customer want to monitor the specific traffic in Internet and we've configured the Netflow in Internet router for those specific IP's. Our Netflow server is configured in DMZ and firewall rule was allowed for port 9996 and 2055 UDP . Fir...
Hi All Good day. We're using 2*5525 ASA's and made into cluster for failover and currently secondary is now Active firewall while Primary is in standby mode (Active/standby). The Active time in primary is XXXX Sec while in secondary is 0Sec which se...
Hi Folks, I wanted to upgrade ASA running firepower services. I had the idea to only upgrade one ASA/FIrepower SErvices and monitor for 24 hours, then upgrade the second ASA/firepower services. Is it possible to operate like this for a short period?F...
Dears, 1) I m facing very strange issues, i have a site to site vpn and it is working fine for my application except for the branch switches and routers for whom i have configured aaa which goes to the ISE server in HQ,when i run a packet tracer the ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 07-16-2025 04:21 AM | ||
| 07-06-2025 01:40 PM | ||
| 07-04-2025 01:59 AM | ||
| 06-19-2025 07:32 AM | ||
| 06-17-2025 01:07 PM |
| User | Count |
|---|---|
| 10 | |
| 7 | |
| 5 | |
| 2 | |
| 1 |
