Hello, I have an inside interface (vlan2) connected to a Linksys router. (security level 0) From the hosts on the ASA (security level 100) I can ping the hosts on the Linksys no problem as this traffic is outbound from the ASA to the Linksys (i.e. ...
Good day!Hi everyone, I would like to seek for your help and advice on how to size and build a BOM for a NGFW and NGIPS.What are the things to consider for the sizing with these given requirements.- Firewall Modes (routed, transparent, virtual firewa...
Hi All We are looking at getting a HA pair of 5506 running the firepower threat defence image. Can anyone tell me if this is stable and ready to use? Can it do site to site vpn to none Cisco devices ? Can they run in a HA pair? Many thanks Carl
Hi guys I have ASA 5545x firewall and need to convert it into forepower...how can i do thar? And how can order? Thnx
- I wish sent the snmp alerts for the port 161 instead port 162 was configured alerts of the system health for snmp, but when the system sends the alerts those alerts go to port 162 snmptrap udp, but the server is waiting the alerts for the port 161 ...
Hello. I get A large number of logs messages (somewhere about 5700 for 30 minutes) "SourceFire has determined not to inspect more traffic of a flow and requests the ASA to stop redirecting the flow of traffic to SFR" from ASA. In FMC there are no ...
Hello I just would like to know if there is a compatibility between my firepower management center and my ASA with FirePOWER device, because currently I cannot add the device to the FMC, and there is an error coming up saying " error in communicati...
hi friends, my ASA 5580 has an INSIDE interface with 192.168.62.254 ip add. and that interf. is connected to a Switch through vlan62 with 192.168.62.253 ip addr. When I connect a PC to vlan62 with a static ip add. (192.168.62.40) and set GW as 192.16...
I've been trying to configured Websense urlfiltering using ZFW feature on my Cisco 881G router. The router is running on IOS 15.0(1)M with Advanced IP Services. And I have confirmed it supports urlfilter feature.This is what I tried to accomplish but...
I've installed update 6.2.0.1-10 on a few devices and the FMC. all of the devices and FMC still show up in the list when I try to update the other devices. If I'm going to 6.2.0.2-51, can I just skip this hotfix, or do i need to keep a list of whic...
Hello, I am looking at moving over to the 5506 asa's now as the 5505's are coming to end of life. I assume a 5506 would quite happily integrate into a network where there is a 5505 running? So a 5506 could have a VPN tunnel into the 5505? What ar...
Hi all;I am asking about the Failover (Active/Active) on asa 5525-x SFR.I am configuring Failover(Active/Active), and make sure that the configuration of the failover is correct, between the tow appliances.But when issuing the command failover on the...
Hello guys! I have a firewall with more tham 1500 rules and a lot of then have 0 hits. I would like to clean the configuration, but I'm noob with firewall and i don´t know if is safe to delete all rules thar there is no hits? Thanks Marcio
How does the term of Firepower subscriptions count down? from the date of purchase or the date of activation? A client has purchased IPS and AMP subscriptions with Firepower 4110 about 3 months ago but none is installed. Do they still have one year t...
Hello, I have a requirement to have 3 ASA or Firepower devices in my environment with their configurations sync'd. Is there any way to have 2 passive devices with 1 active? Any other recommendations to solve this issue? Thx t
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-05-2026 09:59 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM | ||
| 04-22-2026 11:56 AM |
