I don't know too much about Cisco firewall, we are using ASA 5515-X for remote VPN (Anyconnect SSL VPN) with 100 user license. I just want to know, Can we configure the same VPN service on Firepower with no extra license? Thanks
I don't know too much about Cisco firewall, we are using ASA 5515-X for remote VPN (Anyconnect SSL VPN) with 100 user license. I just want to know, Can we configure the same VPN service on Firepower with no extra license? Thanks
Hi, just want to know in ASA what is the more preferred route a PBR or a directly connected route? thank you very much
Do the licenses I bought for my 5505 transfer for no added fee to my 5506 when I upgrade?
Hello,Im Looking to find out what Devices are needed for a ccnp security home lab. I keep hearing that 2 5510's are a must for labbing. The downside Is the Prices avg $800 each on the low end. I also saw some ppl had an ips in their lab. Im looking t...
Hi All, Would you be able to shed some light on the below error message? If you could look at the screenshot attached, it will show you the current setup. I have set this up using the ASDM, the packet is being denied when going from: Outside R1 to ...
Good Day, I have a concern from my customer, claiming that the memory usage from CLI and meanwhile GUI shows that the memory is normal. And now my customer also claims that the software doesn't tally to the hardware. Any way in particular that I can...
Dear, I have a question about “Block and Allow Lists with URL filter function on ASA w/ FirePower” When we using “URL Filter function”, is possible to we can create manual url filter rule(or access list) as like bellows? Allow to http://hosta.c...
Hello everyone, I have two ASA 5516-X setup in an active/active failover. I have also installed and succesfully bootstrapped the firesight management center with the two sfr modules added and licensed. And, at this moment I am reading through the f...
hi i am trying to reset the password for admin user (for the web interface) for my firepower mgmt center with the following command sudo usertool.pl -p 'admin Sourcefire' but when i run it i see the following error message Password length is 0 at...
Hi. I am working my way through the 45-day eval of an ASA5506 Firepower IPS and have resolved most of the problems. One issue still remains: Even though ">show time" displays correct time for both UTC and local, all syslog messages are stamped with ...
hi, i facing a PBR issue on ASA, as i know , the normal PBR format is: access-list to_ADSL extended permit ip 192.168.1.0 255.255.255.0 any route-map my_map permit 100 match ip address to_ADSL set ip next-hop 100.0.0.1 then apply it on the interfac...
Hello, I am in need to verify that I have configured our ipsec tunnel to be FIPS compliant. Here is a sample that I created to make sure I am good: crypto ipsec ikev2 ipsec-proposal testing protocol esp encryption aes-256 aes-192 protocol esp integr...
Hi Team, Can you please let me know, how to downgrade the Cisco FirePOWER 7020 sensor from 6.0.0 Build to 5.4.0.9 remotely. Request to share the steps involved in downgrading remotely, as I don't have physical access to the device. Thanks, Murali ...
Hi, Based on the attached screenshot on the report. What is the root cause IP and destination IP for faceboook application ? Can we find in the firesight analysis ? Appreaciate it thank you
Dears , i want to know which privilege i suppose to use to allow certain user to do "sh version" command as i tried some privilege and they all do the same as privilege 15
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 12-31-2025 01:53 AM | ||
| 12-15-2025 09:32 PM | ||
| 12-11-2025 07:27 AM | ||
| 11-13-2025 12:52 PM | ||
| 11-03-2025 09:48 AM |
| User | Count |
|---|---|
| 4 | |
| 3 | |
| 2 | |
| 2 | |
| 1 |