Good morning,I have10 WS-SVC-FWM-1 modules, and I'm looking for a resource/walkthrough on how to go about requesting and applying a license to the modules. Thanks for the help!-Scotty
Dear Expert,I meet one issue regarding Failover Switch-Over.When my ASA-Primary down, it will ASA-Secondary take over on ASA-Primary.Then when ASA-Primary up back, ASA-Secondary still as Active.Do you have any idea to advice how to make Primary to be...
Hello,I planed to upgrade the ASA5520, 512 MB RAM, CPU Pentium 4 Celeron 2000 MHzInternal ATA Compact Flash, 64MB which met the minimum requirement to upgrade it, I installed the image asa721-k8.bin successfully but once I issued the command (boot sy...
Hello allI appreciate there are numerous discussions on this, however, I'm yet to find a solution to my problem. We have a pair of 5585-Xs configured in a active/standby cluster. On each physical device we have a port-channel going up to a Nexus 5K. ...
Hi Does anyone knows where to get information about a Firepower IPS?, Ive been getting a lot of signatures from my IDS like BLACKLIST DNS request for known malware domain did.ijinshan.com - Win.Trojan.Jadtre (1:33881:1)BLACKLIST User-Agent known mal...
Our company has purchased the above Cisco product and carried out the installation and configuration thereof in strict accordance with written guidelines. However, the ASA FirePOWER configuration module in ASDM has shown only the contents, whereas th...
I have an ASA version 9.0.1 and I need a way for the DMZ to talk to the Outside network. This is what I have so far but it is not working.access-list outside_access_in_1 extended permit tcp any host 1.2.3.1 anyaccess-group outside_access_in_1 in int...
Hello,We had an issue today at one of the unmanned locations. When the local tech went on site he was not able to reach anything on the internet. I started troubleshooting and noticed no entries in the xlate table. The NAT statements were all correct...
Hi . I want to know ASA5550 Nat Table Limit connection. i search ASA5550 datasheet. but i can't find NAT table.Below is ASA5550 . License is default (Premium License)====================================================================Cisco Adaptive...
We have a rule in our firewall to NAT an IP for a system on the inside to the IP address of our outside interface so that users may publicly access the system via a web browse using the outside interface IP with port 8100. It was working but the NA...
Hi,Iam getting Command authorization failed after adding "aaa authorization command TACACS+ LOCAL" on asa firewall.Added the firewall in tacacs server.
Hi In ASA55555, the output of command show arp is as following. Based on these results, how can we know its neighbor ? Thank you inside 192.30.11.3 xxxx.xxxx.xxxx 649inside 192.30.11.1 yyyy.yyyy.yyyy 7399management 192.31.10.12 zzzz.zzzz.zzzz 4189man...
Hello,I need to separate some wireless traffic on a ASA 5520 which is currently hitting our inside network, I would like to move this specific traffic to the DMZ.Currently I have an Interface named as DMZ, I am looking to create an sub-interface so I...
Dear Expert,Can I configure Failover on ASA 5505 with different RAM:ASA-1 = 512MBASA-2 = 256MBBeside of that problem is correctly.Best Regards,Chhayheng
Dear Sir/Madam, I want to limit dynamic PAT port range like below global (outside) 4 10.16.1.16 netmask 255.255.255.255 nat (inside) 4 access-list test I want to use 10.16.1.16 port from 10000 to 60000. or i just don't want to use p...
