Buy or Renew
Buy or Renew

Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

“Join

 
Labels

Forum Posts

Start a conversation

Resolved! Pinhole timeout

Hi,What does a pinhole timeout indicate?Aug 19 2011 07:44:22: %ASA-6-302014: Teardown TCP connection 54522 for outside:192.168.25.22/0 to inside:192.168.125.12/49158 duration 0:02:01 bytes 0 Pinhole timeoutAug 19 2011 07:44:22: %ASA-6-302014: Teardow...

lcaruso by • Level 6
  • 17079 Views
  • 3 replies
  • 0 Helpful votes

ASA MSSQL Inspection

Hello everybody, As far as I know there is no Deep Inspection engine for MSSQL in Cisco ASA, so here arise a question. How to inspect MSSQL traffic in Cisco ASA or better to say how to inspect a custom service or port , where there is no Deep Inspec...

Resolved! ASA 5540 - config issue

Hi Experts, When I do a show run these are the only options shown..! The problem is that I am unable to configure the interface? Interface configuration commands:  default      Set a command to its defaults  description  Interface specific descripti...

Resolved! is ASASM support clustering ?

can i configure two ASA services module sitting in on chassis (6506-E with 720-10G) as clustering ? or has to use VSS mode  ?  any config example link?  Tried search online but can not find any related to ASASM case   Thanks

Rico Hao by • Level 1
  • 546 Views
  • 1 replies
  • 0 Helpful votes

Resolved! ASA 5506-x

Hi,  I'm preparing a CCIE security lab and I'm thinking about buying the 5506-x to practice with it so I will need some insight from you guys about the product. I have some questions about it:  1-Is the CX context aware supported on this model. Do I...

NETAD by • Level 4
  • 2248 Views
  • 9 replies
  • 0 Helpful votes

ASA 5545X upgrade

Hi everyone. I have a pair of 5545x in HA. I want to perform a software upgrade from version 9.1(2) to 9.5(2) with zero downtime. I was wondering if it is possible to perform this upgrade directly or if I have to go through all the minor releases fir...

Resolved! FirePOWER installation

Hey everyone I have ordered FirePOWER for my 5555-X and recived a SSD disk and a PAK number. I think I heard somewhere that i need two 120SSD disks, I only have one. Is it enough ? And is this the correct order: 1. Shutdown/uninstall old IPS 2. In...

Cisco SLM2008 has Port 0 open

Hi there, I have made some vulenerability Scans in my company and we use some cisco SLM2008 switches. Openvas shows me that there is port 0 open. How could this be. It says that Port 0 is sometimes used for backdoors. TCP port 0 is opene on the re...

mleek0001 by • Level 1
  • 627 Views
  • 0 replies
  • 0 Helpful votes

Resolved! Reverse path check error?

All, I am getting the following error message on my firewall: 1 Feb 01 2016 12:19:36 106021 1.1.1.1  2.2.2.2  Deny ICMP reverse path check from 1.1.1.1 to 2.2.2.2 on interface INTERFACE I am struggling to see anything obvious at fault. I have acces...

drbabbers by • Level 3
  • 798 Views
  • 4 replies
  • 0 Helpful votes

ASA 5506W-X

I have recently received delivery of several 5506W-X firewalls, my plan was to install them at remote sites with EasyVPN Client enabled. I updated the firewall to IOS 9.5(1)  and proceeded to setup the Firewall, Inside/Outside interface, the one site...

Load more
Review Cisco Networking for a $25 gift card