Network Security

Engage with peers and experts on network security topics such as FTD, FMC, FDM, CDO and ASA.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Enabling our customers to leverage their install base and take them to the next level with Cisco Secure Firewall Threat Defense has always been a key priority.  The migration tool is available for download to migrate the configuration on the on-premi...

gopaks by Cisco Employee
  • 307 Views
  • 0 replies
  • 4 Helpful votes

I currently have a Cisco ASA 5505 setup with a Site to Site VPN to a remote branch and the tunnels are live and working fine currently.I can access machines on the other branch subnet as well as ping anything on it but I cannot tcp/80 (HTTP) into any...

New to the Virtual Defense Center and ASA Policies/Rules. Looking for tips and best practices on the setup of policies and rules in my Virtual Defense Center. Not seeing very much traffic as far as Malware and File Events, which could be a really goo...

Eric York by Level 1
  • 1798 Views
  • 8 replies
  • 0 Helpful votes

Hi As we know, failover has special ip address to connect primary asa and second asa. For example 1.1.1.1 and 1.1.1.2. Do you think that other device or other failover asa can use the 1.1.1.1 and 1.1.1.2 in the local network ? Thank you. 

eigrpy by Level 4
  • 280 Views
  • 3 replies
  • 0 Helpful votes

HiI am new to configuring Anyconnect VPN using the command line. Previously I have just used the Anyconnect Wizard using ASDM. I need to configure anyconnect VPN and I want to start using the command line. I have 2 questions for anyone kind enough to...

Hello community I am not being able to add our  ASA 5585-X Cluster to CSM. we are running ASA 9.2.2.4 and CSM 4.7. (error on the print screen). Do you think an upgrade will help? As anyone tried or found a solution for this? Best regards Isaac 

Hello Experts,My question is how to enable traceroute on cisco ASA. I have seen alot of examples which allow traceroute through the ASA. However i am looking to enable traceroute on ASA itself. Like if i have an outside interface with IP 1.1.1.1 i co...

Hello guys!,do you know how can I set a pre-shared key for tunnel-group DefaultL2LGroup using Cisco Security Manager CSM 4.8?I know I can apply a Flexconfig containing the commands, like:tunnel-group DefaultL2LGroup ipsec-attributes ikev1 pre-shared-...

Hi Guys, Can you please help me with configuring a asa 5505 8.2(5) with a range of ports.I have set ACL -  access-list firewall extended permit tcp host 1.1.1.1 host 2.2.2.2 range 4800 4900what is the easiest way to add the static (inside,outside) fo...

ohgroup01 by Level 1
  • 257 Views
  • 1 replies
  • 0 Helpful votes

hi, guys i have 6509 chassis and FWSM(software 3.2?) i did clearing configurations on FWSM all.... and after that, i can't access to FWSMNow, i want your help for solving this problem... and tell me how to access to FWSM please, help me , Thanks for ...

jjy000001 by Level 1
  • 671 Views
  • 1 replies
  • 0 Helpful votes

I am trying to peer a Cisco ASAv with another Cisco ASAv via EIGRP.  One of the ASAv (lets say A1) is peering with a NX-OS via EIGRP without a problem but when I try to peer it with another ASA on a separate interface, the ASA is not sending hellos (...