Hi there... I have recently installed a 5506 at a customer WHO has two servers that needs NAT. One of them is a web server on a DMZ and i have enabled NAT with a public ip on src: DMZ, dest.:OUTSIDE. Also i have made two access rules that allows OUTS...
We have Cisco WS-C3850-48T L3 switch and i am going to configure PBR on it, does anyone know what could be the impact? If i apply policy to specific interface then PBR will only apply on that specific interface traffic right? it won't apply on global...
Hello, can someone please explain to me what the Product code L-ASAV5S-STD-8 means? What does 8-pack mean (8 Users, 8 Hosts, 8 Ports,...)? I would like to set up a virtual lab for Proof of concepts, Testing and Troubleshooting. I'm just a freelancer...
Hi, I recall reading wccp can only redirect to the ASA inside. On the new 5506 that have no switch ports, this creates an issue where a webfilter was directly connected previously and obviously cannot now. Is that wccp restriction truly only inside?...
Hey guys, I'd like some help with port forwarding on a 5505 running 9.2(4) code. I'm trying to forward requests on port 80 on my outside, ISP provided IP to port 8000 on an internal server. Everything inside the ASA is PATing on the outside address. ...
We have external customers that access to our ASA public "outside" IP to reach web servers within our DMZ . Trust is enabled with public certificates assigned on the "outside" interface. We also have external employees that need to connect to this sa...
Hi all, Please is there any solution, how to block a website on specific time (for example only between 12:00PM and 14:00PM, we can open a specific website, after this time it becomes blocked) Thanks in advance
Hi Team, I have downloaded the Firesight Management Center Virtual file but I can´t open it. The extension is ¨.SH¨ as you can see in fhe following information that I´ve obtained from Cisco.com web page: Cisco FireSIGHT Management Center Patch Sourc...
My customer Sourcefire 3D7120 sensor GUI admin could not login ( message : unable to authorize access) ,but ssh admin login OK. Any suggestions?
Hi All, I have an ASA with an outside, DMZ and inside interface configured and acting as my core internet firewall. I have an FTP server in the DMZ that outside users are permitted to use. Outside security level is 0, DMZ 50, inside 100. My ACL for...
Hi Guys, I have a question about VDB updates, on the documentation I found that after downloading and installing VDB updates, we have to reapply the access control policy manually. Does that apply too if we do the update via task scheduler using 2 se...
Hi!! What are the log messages for CPU usage, memory usage, free memory and what basis we are getting the system resources graphsPlease help me out. Regards,Shalendra
Hi, Can you share the failover configuration for ASA firewall. Incase if any of the interface on primary(active) firewall fails it should switch over to secondary(standby) host.
Hi all, I would like to kindly ask you for help with configuration of Cisco ASA 5505. Need to say that I am beginner in ASA networking I have standard network model configured on ASA. DMZ,OUTSIDE,INSIDE. In DMZ I have application server which needs t...
i am using cisco anyconnect with IKEv2 (ios 9.5,anyconnect 4.2) .this configuration will support hotscan and CSD.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 07-16-2026 06:39 AM | ||
| 07-15-2026 08:48 AM | ||
| 07-13-2026 11:05 AM | ||
| 06-24-2026 08:00 AM | ||
| 05-26-2026 07:54 AM |
| User | Count |
|---|---|
| 2 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |
