Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Hi,I have issue with with small 8-port switches and port authentication with EAP-TLS.  Error:  %AUTHMGR-7-RESULT: Authentication result 'no-response' from 'dot1x' for clientError:  %AUTHMGR-7-RESULT: Authentication result 'timeout' from 'dot1x' for c...

smanasijevic by Community Member
  • 1397 Views
  • 3 replies
  • 0 Helpful votes

Hi All, We have a ASA 5525-x with the CX module which ahs been in operation for a year now with Access, Identity and Decryption policies set up and its been working perfectly. We redirect all traffic from the ASA to the CX in our policy. Since yester...

Fraser010 by Community Member
  • 729 Views
  • 3 replies
  • 0 Helpful votes

I've been stuck with Fortigates for awhile and had to help a customer with their ASA setup.   They state that Guest interface can reach inside hosts/servers.. And when I check, I see that we have no NAT statement between Guest and Inside networks.   ...

azore2007 by Level 3
  • 1646 Views
  • 5 replies
  • 0 Helpful votes

Hello All, I have two default routes on ASA pointing to two different ISP s with different metrics.The hosts pointing to the default route with metric 1 are able to access the internet to and fro,however the hosts pointing to default route with metri...

mudasir05 by Level 4
  • 1548 Views
  • 7 replies
  • 0 Helpful votes

Hi guys,I am new to this group. I have a question and believe it is related to the firewall. I need 443 routed internally. The connection is working with 80 but not 443. Please check the picture attached. The command existing in the firewall is acces...

venkat257 by Community Member
  • 1385 Views
  • 6 replies
  • 0 Helpful votes

I would like to allow RDP in from only a specified IP.  Right now RDP is not allowed from any IP, but SSH is allowed in FastEthernet 0/0 is my WAN interface interface FastEthernet0/0 ip address dhcp ip access-group Block_Stuff in!ip nat inside source...

Resolved! ACL Not working

I would like to allow RDP in from only a specified IP.  Right now RDP is not allowed from any IP, but SSH is allowed in FastEthernet 0/0 is my WAN interface interface FastEthernet0/0 ip address dhcp ip access-group Block_Stuff in!ip nat inside source...

In the ACS version 5.4, how the user passwords on internal database are protected?Does the ACS is using administration password  or algorithm AES for encrypt the users paswords on internal database ?Thanks for you help

santacho87 by Community Member
  • 740 Views
  • 2 replies
  • 0 Helpful votes

Hi All, I have a Cisco ASA 5510 running on 9.1(5) image on it with ASDM 7.5(1). I am trying to open ASDM but it is not working. Java plugin is downloading and cached software is loading but after that it is not opening full ASDM console. Need your su...

I have free 1TB disk in my ESXi  Server. When I upload Firepower image (Sourcefire_Defense_Center_Virtual64_VMware-ESXi-X.X.X-xxx.ovf)  and extend to 900GB.  when I boot Sourcefire Defense center and I check it free disk, it show free 2xx GB. How can...

Sun_Clony by Community Member
  • 1255 Views
  • 1 replies
  • 0 Helpful votes

Hi, I have nexus core with multiple vlans configured on it. Cisco asa firewall is connected with core using port-channel and trunk. How can  I make all vlans traffic routable on firewall? I will use IP address at port-channel interface? how firewall ...

Rizwan by Level 4
  • 3162 Views
  • 18 replies
  • 0 Helpful votes

Hi everyone, i just have a problem with the CX reauthentication: wenn i login with one AD Account and also use the one to get the Internet, and i logout and use other AD Account, i get no new authentication for Internet, wenn i start the Firefox, and...

lupingyao by Level 3
  • 623 Views
  • 2 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card