HiI'm in the process of migrating Watchguard firewalls to ASA. I have noticed in the policies that some private IPs are natted to the same private IP as follows:99.98.97.96 > 192.168.10.1 = FTP99.98.97.96 > 192.168.10.1 = RDP99.98.97.96 > 192.168.10....
Hi community,This thread is for all of us who always puzzles over which 9.x version I have to take for my ASA 5500-X NGFW. (In my case 5545-X)The wish is to get the best minor version - best maintenance/updated, stable and suited version without to r...
Hi I have a set up with three ASAs in total. Two on the main site set up using HA and another ASA at a DR site which is connected if DR is invoked.My question is can I restore a backed up config from the HA pair to the singular ASA. The complication ...
I'm trying to pass FTP traffic between interfaces of an ASA5525-X (ASA v9.4(1)), but Passive Mode isn't working (Stucks on "Retrieving directory listing").The ACL allows FTP and FTP-Data (Required for Active Mode, which is working fine). Here is the ...
HiSo all of a sudden I have been thrown onto firewall projects so in the deep end. I have a few questions popping up here and there and would be nice if anyone can help1) For a Static NAT, to an internal server, Do I require a single inside to outsid...
Hi Everyone, I bought this moduleASA SSM 10 for 5510 I inserted this to the Cisco ASA 5510 and rebooted it.when i do sh inven it shows module is there. Need to know how can i access the ssm module from firewall command prompt?Also need to know how ca...
Hi,I am upgrading ASA from 5510 to 5512.I have copied all config over to the new device, manually changed some interface settings etc.The question is what do I need to do regarding the Anyconnect licenses and Certificate used for VPN? And can I do th...
Hello Everyone,We have PIX-525 Active-Passive Firewall Pair. Recently, i changed the Public IP Configuration, Access Lists & NAT-ing configuration in the Active (Primary) Firewall. While doing the changes on the Active Firewall, the Secondary FW was ...
Hi I am in the process of replacing some Watchguard firewalls with ASA firewalls. I have noticed a few static NAT rules on the Watchguard using the same public IP address but each NAT uses a different private IP Address.e.g98.98.98.1 > 192.168.10.198...
I have all the existing access rules on both active and standby ASA 5550 Firewall with the outside interface configured as access port level previously. However, I intend to convert this access port level to a trunk port level between the Cisco Swit...
Hi,Our have a software must setup a public IP address to connect the inside server (assigned a inside IP address) at outside, that made the NAT on the outside ASA 5505 fw.inside server (192.168.10.152) --- FW (NAT 1:1 192.168.10.152 <> 202.32.48.152...
If there is a SFR module failure or some other event that requires an SNMP trap to be generated , is it the ASA host that sends the trap or the SFR individual module?
Hello everyone,I'm looking to purchase ASA 5516-X with FirePower. I have a couple questions, please bear with me since I'm new with the ASA-X version: 1. According to the sales engineer that I'm talking to, he said that I don't need to have a physica...
I'm moving from a ASA 5510 v8.2 to a ASA 5525-X v9.4 Short of putting in the 8.2 config in the 9.4 unit and picking up the Pieces, is there a preferred method to Migrate the config from 8.2 to 9.4? I know the was Significant NAT changes. Thanks!
Below is my problem. The ASA can not restart, reboot or recover the sfr module. I can console into the module but restarting it there does nothing. I'm awaiting a maintenance window to restart the whole ASA and see if that will fix it. Module sf...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-31-2026 07:16 AM | ||
| 05-26-2026 07:54 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM |
