Hello All,On ASA 5515 version 8.6, I am trying to create a NAT and access list to allow RDP from outside public to inside private network.I was able to create it using the ASDM as I am comfortable with it and not a expert with CLI.When I tested it, i...
Hi guys,I am currently working on converting watchguards to ASA's. The current Watchguard is setup with two Internet connections. One is the primary, the other is the secondary.All outgoing connections go out the primary (listed as #1 on the WAN fail...
After deploying a FireSIGHT System with Fiber Network Module (Netmod), connection is lost between the end devices.
Hello everyone,I'm having some trouble and need your assistance.We have thirty five HTTP/HTTPS/FTPS web sites to setup in the ASA 5520 ASDM firewall, we need to know if its possible to have them all setup without using a DMZ, we have two or three sub...
Hi team, In my office we have active and passive ASA 5540 with version 8.2(5).Now I plan to purchase anyconnect license. In the document, they clearly mentioned version 8.3 and above, we need to purchase one license passive will automatically sink.in...
Hello, I have a HA pair of Cisco ASA 5510's and the configurations are identical. The customer has about 100 vpn tunnels on the ASA. There was a link failure on the primary firewall and had to failover to the secondary but when it failed over, only a...
We have an odd issue which began by being unable to remotely connect to the ASA via ASDM or SSH. SSH prompts for username and password, but returns 'access denied' even when using the correct password. Logging into the console to troubleshoot, we f...
Can you do URL redirection on an ASA 5505?Here is the scenario. In our home office we are implementing NAC using Aruba ClearPass. So when a laptop plugs in to a wired port it gets a dhcp address and it's gateway is the Aruba Controller, which then se...
Hi guys,I'm looking for some advice regarding the deployment of an ASA. I have two networks separated by a routed link (layer 3 switch to layer 3 switch). I would like to deploy an ASA between the two networks for increased security. I'm leaning towa...
We have an ASA5510 v9.14 and are looking at setting up a second unit to run in active/active.The ASA has site-site vpns, most static end points, but we have several dynamic site-site vpns. We also have SSL anyconnect users and staff use cisco vpn cl...
Hi folks, I have the following topology;IP Phones--->Call Manager--->Cisco CUBE--->Firewall ASA--->Internet<---VOIP ISP. We want to establish a SIP Trunk between the CUBE and the VOIP ISP. We already managed to register with the ISP, but we can´t est...
Hello, i have ASA 5525-x and i am trying to route traffic between outside and inside interface, in the essence i want it to behave like router. So on the public interface i have 10.47.0.2 which connect to some other private IPs and on the internal in...
Find the ASA int configuration all networks getting internet but from 5.0 network to 40.0 network unable to access from 5.0 and 40.0 network 192.168.1.2 interface not able to ping . CISCOASA-5525# sh run int!interface GigabitEthernet0/0 description W...
Appreciate any help with active/standby config. I just finish configuring the firewall and everything is tested fine but then I noticed the failover status (shown below) shows the standby unit as failed. The configuration between the two unit synch ...
When I attempt to create an RNA detection policy, I receive the following error message on the web interface of my Sourcefire 3D System:Error 500: Internal Server Error
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-06-2026 12:20 AM | ||
| 09-22-2026 04:13 PM | ||
| 08-25-2026 06:22 PM | ||
| 08-24-2026 12:26 AM | ||
| 08-20-2026 05:54 AM |
| User | Count |
|---|---|
| 2 | |
| 1 | |
| 1 | |
| 1 | |
| 1 |
