Hi, i have a C1921 router and i would like to have ACL that dines some IPs and some MACs on internal interface. Is that possible to do? I know that you can have only 1 ACL per interface and that probably you can't combine MAC and Ip addresses in one ...
Hi,Our firewall Memory utilization is 195MB/256MB .Is this normal? How can identify this utilized traffics in detail?Regards,vijesh
After a recent firewall cleanup we now are failing a PCI Scan from Trustwave. I have created a rule to allow their IP's to come in any port and I am still getting a "Network Service Stopped Responding" on there end while they are going to our Public ...
I 'm flood from random adresse IP in TCP/61137what can i do with the asa5520 my appliance security ?
Does anyone know if Cisco has the PBR feature road mapped for future IOS releases or if they are building in new feature sets to load balance 2 different ISP connections much like F5. It seems more and more customers are asking for all in one functio...
I am trying to create a PCI zone inside a network. I am using a 1941 with security and ZFW to restrict traffic. PCI can go out to ASA and across to LAN. LAN can go to ASA but not to PCI, finally ASA can go back to both PCI and LAN to send natted traf...
I have two ISPs but I don't want to setup a backup route I want to route all my internet traffic out the secondary outside interface but without losing the first outside interface because I have all of my static IP addresses on the first outside inte...
Using ASA 5540 and we are currently at version 8.4(1) but we want to upgrade to version 9.1(5) so was just to ask if you can please confirm the recommended memory and flash required.And being a newbie on the ASA is this a easy enough process to do? A...
Hello!Is it possible for AIP-SSM to see all messages that module generates during boot process? I need to obtain output similar to output that appliance (IPS4345 or other) sends to console session during boot.I tried executing "debug module-boot 255"...
ASA is 5510, ver 8.3(1), I can't forward ports (www, ftp) from outside to DMZ.My configuration:outside: IP Public (X.X.X.X)DMZ: 10.10.10.0/24access-list outside-in extended permit tcp any interface outside eq wwwaccess-group outside-in in interface...
Hi All,ASA version 9 now includes the next generation (suite B) for encryption.I have found the following Q&A:Q. Is next generation encryption available on all ASA platforms?A. No. Next Generation Encryption is fully supported on the ASA 5585-X, 5500...
Hi , I have configured the Remote IPsec vpn on my firewall asa 5510. i have configured the standard acl for accessing the internet network. i am able to connect the vpn, able to access the lan devices as well but when i tried to connect to the firewa...
Hi All,Firewall rookie here. I am setting up two mock sites to talk to each other, and I am having a very basic problem: I can't ping the outside interface IP (vlan 2) on my ASA from my PC that is directly attached to the inside (vlan 1) interface o...
Hello,I am new to ASA configuration. The question I have is that:1. The auto nat that we configure under "object network", does it mean that traffic sourced from only subnet/host that match that network object under which nat is configured will be tr...
I was wondering if the Cisco ASA 5525-X 9.1(2) supports a URL as a destination or source, we ran into an issue where a domain name IP changed and it took down a critical application. As of right now I have two of the IPs in the ACL that are owned by ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 08-10-2026 08:58 AM | ||
| 08-10-2026 02:48 AM | ||
| 07-22-2026 05:00 AM | ||
| 07-16-2026 06:39 AM | ||
| 07-15-2026 08:48 AM |
| User | Count |
|---|---|
| 4 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |
