Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Hi,In order to standardized/secure the ASA configurations, I am going to deploy the attached commands to several ASA from version 8.0 to 8.4. Although I have tested them and they work ok, but as precaution please advice that these commands will not d...

raza555 by Level 5
  • 1631 Views
  • 1 replies
  • 0 Helpful votes

Hi All,Hope Everyone is Well?Hope somebody could help as im banging my head with this one:-I have several Sub Interfaces for VLAN's Setup on my Firewall. I have these connected to a Switch, which inturn has the Switch Port set in Trunk Mode,Switch Co...

simon.green by Community Member
  • 3198 Views
  • 10 replies
  • 0 Helpful votes

Hi everyone,I have configured Remote VPN access.Inside interface and vpn pool is 10.0.0.0 subnet.ASA inside interface has NAT exempt as per config belownat (inside,outside) source static NETWORK_OBJ_10.0.0.0_24 NETWORK_OBJ_10.0.0.0_24 destination sta...

mahesh18 by Level 7
  • 3939 Views
  • 6 replies
  • 0 Helpful votes

Hi,We have bought a Cisco ASA5512 from our supplier which comes with the IPS and the license.When i login using session ips command i get the following.***LICENSE NOTICE***There is no license key installed on this IPS platform.The system will continu...

I would like to better understand failover polling with the ASA.failover polltime unit 1 holdtime 15failover polltime interface 5 holdtime 25UnitWhat is being polled? An IP address? Which?How is the unit being monitored? ICMP?InterfaceHow are the int...

rmeans by Level 6
  • 749 Views
  • 0 replies
  • 0 Helpful votes

I always used ASDM wizard to create IPsec to branch office.    For example, I have one brance office (10.3.3.0/24)  --------- IPsec ---------------- HQ (10.0.0.0/8)  Whenever I created a IPsec through ASDM wizard, I could see always NAT Exempt  sourc...

Resolved! Checkpoint and ASA

Inside I have 2 networks: 10.10.x.x and a 10.199.x.xMy ASA interfaces was the following:E0/0 Public IPE0/1 10.199.1.2/24E0/2 10.10.144.47/22I put a checkpoint in front of the ASA and changed to the following:Checkpoint Ext. 10.10.144.47/22Checkpoint ...

Hello all ,                                             internet router-----------outside------------- ASA -------inside-------------cisco 3750 (----A----)                                                                                               ...

Hi ,I am using ASA 5520 version 9.1(2) and configured the static Pat to access the internal server with the specified port from the public ip address (5.x.x.x) , able to Telnet with port (telnet 6.x.x.x 8100), but cannot access the server from the 5....

msameerkn by Frequent Visitor
  • 4443 Views
  • 14 replies
  • 0 Helpful votes

I was testing to see if I was having asymmetric routing to an ASA inside interface from a router. The following does not work andon the ASA I get error ASA-3-313001: Denied ICMP type=8, code=0 ....R1#ping Protocol [ip]: Target IP address: x.x.x.x Rep...

xayavongp by Level 3
  • 1826 Views
  • 3 replies
  • 0 Helpful votes