I just wanted to reach out and run past something past you all for some advice. In the site we had a breach where hackers got remote access to a laptop on the internal network and attacked a few other devices powered on the network. That laptop was ...
Forum Posts
We have a Firepower 4120 unit in a pair that has failed for RAM failure after an FXOS upgarde. What is the best approach to replace the unit considering that it has multiple instances running?I understand we can use the same SSD from the faulty unit ...
i have 2 asa in active/active modecontext1 active in ASA1(primary unit)context2 active in ASA2(sec unit)everything is okwhen failover link will be down , primary and secondry unit will be active for both of them ( it is normal behavior )but i want wh...
Hello everyone.This is a lab test using FDM 7.2.0-82 firmware on FPR 2110.The lab test environment was created like this.1. The 10.10.10.1/30 Routed interface named Inside.2. 10.111.111.2/30 Routed interface named rip-test-out.3. L3 (C9300) equipment...
Hello.I have ASA5506-X with FTD image installed. I connected it to my smart account and now activate 3DES license (PAKs or Tokens->Get Licenses->Crypto,IPSec->Cisco ASA 3DES/AES License->[enter sn]->next).Then: Add new PAK->[fill PAK, pin]->finish. C...
Hello, I wish to access the API of Firepower2140 to make backups via an open-source application.Is the API feature enabled by default to run curl requests?Also, is there a URL to list all possible API requests? Best Regards, José
Resolved! FMC Managed FTD No Stats Portchannel
I noticed that my FTD's do not show any traffic stats when running the command show interface in the FTD cli. I only see traffic stats on the sub interfaces of the portchannel. It seems very unusual to not see any stats on the portchannel interfac...
Hello everybody, our customer has FMCv (rel. 6.6.7) and two ASA5525 (rel. 6.6.7).(see screendump) Even if the ASAs do not use Smart Licensing I get the following error message in the Health Monitor (see Licensing ScreenDumps): Critical Modules:1,Norm...
Hi,A few users are getting blank page when trying to click connect in Cisco AnyConnect application (4.10.05111) using Windows 10 machines. Uninstalling and reinstalling the application seems to be working only till the next reboot.Any suggestions?Tha...
hi out thereI have just upgraded our HA FMC 2600 fro 6.6.5 to 7.0.0 - and had a few problems since the HA part certainly not upgraded as expected. When I had upgraded the standby device from 6.6.5 to 7.0.0 and I got it into sync again it refused to ...
Resolved! how to update ips database on cisco fmc
We have an ips license for the cisco fmc and we have configured and have applied the ips but we don't know how to update the ips database. Help on this is much appreciated.
HejI am testing what traffic to allow and block directly with the block. I have the below configuration that should in theory block all traffic to device from a neighbor including BGP. But regardless the BGP session stays up .I am wondering what I am...
I recently change the management IP address of our firepower appliance and can no longer access the firepower manager GUI on the new address.I can ssh to this address perfectly fine and can see that the firepower has https services enabled. i did dis...
Resolved! FTD Transparent Mode (TRUNK)
Scenario....I have 2 switches (Switch A and Switch B), they are connected together via a TRUNK allowing vlan 10 and 20 to traverse between them. I want to insert an FTD between the switches in transparent mode. I'm having a heck of a time finding d...
Resolved! firewall that support L4-L7
Hello i want to know what are the firewall that support L4-L7 either Cisco or another manufacturer ??? i want to knwo if ASA or FTD support L4-L7 ??? i wait a reply from expert security Thanks
