When i install my ASA5505 i get the following message, could you help me please?"This platform has a Base license.Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0) Boot microcode : CNlite-M...
Hi all. I am using Qemu emulation of ASA. Kindly tell me if following scenario is a bug or something legitimateMy topology is PC ------------------------e0/0 ASA e0/1------------------------------R2 inside ...
Hey guys, I cannot seem to determine exacly why I am not able to ping from the inside to outside using the standard 100/0 security levels respectively.I am dynamic natting the inside to the outside interface, something I don't usually do but cannot s...
Hi Guys,Currently we are running one ISP which incoming and outgoing traffice will go throught the ISP, lets call it ISP1.We have this VC network and the traffic are very low and we was thinking to shift the web services incoming traffice to this tra...
Hi All,Do you have any idea how to bypass lost password on Cisco Security Agent version 6.0 without reinstalling the image?Thank you.Dexter
Hi ExpertsI Have web server (linux) sits in the DMZ (asa 5520) segment and this server should be accessible form the internet, 1)how to make this server https based access over SSL2)how to protect this server form network and security standpoint?tha...
I am looking at the datasheet of IPS 4255 and found that for automated fail-open a third party product is required I do not understand what third party is needed does this mean that IPS4255 does not do fail-open when the sensor fails? I could not fin...
Hi to all I want block some pages type (social networks,internet radio and TV) and application with instant message like (messenger and web chats), now i have a Cisco ASA 5520 version 8.2. I trying to make this CLI configuration< http://www.cisco.c...
We have a Mitell Border Gateway in our DMZ configured to accept teleworker connections. I have it all configured, but I get one way com errors on the Mitel border gateway when i try to place a call to a teleworker(phone set up out...
HiAfter I have upgraded our ASA 5510 to 8.4.2 I have problem with the management interface.Our former firmware 8.2.3 had no problem using the management interface as a DMZ zone, but after we upgraded to 8.4.2 we can't make it work.The interface and t...
Hi,On my production environment I have a firewall with already two contexts defined (15% of CPU used) and I want to add a new one. This context is going to use the same interfaces as the others contexts. When I will enable the context, can I have som...
hello, I am running into a issue that I cannot seem to figure out. I have a asa 5505 with the Security Plus license. I setup a native vlan where all of my network devices sit on. ie my Wireless Access point has an ip of 192.168.3.2, my switch .3. I h...
I am about to replace the supervisor engine in our pair of distribution switches in our data center. We currently have a FWSM module installed in each of my distribution switches running 3.1(20) code. The old sup720 are running 8.6(4) and the mfsc ar...
Normally I do not use the Asa names function. I have no names enabled on the cli. The customer added a name to an ip in what I saw the correct way to do it under network objects in asdm. When they did this it added the name (text) (ipadd) to the cl...
Hello,I need help configuring a newly reinstated PIX515E with IOS 6.3 to test the configuration of a load balancer.I would like to setup with two Inside interfaces (or simply two interfaces) for testing. I just need it to pass traffic (basically HTTP...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-05-2026 09:59 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM | ||
| 04-22-2026 11:56 AM |
| User | Count |
|---|---|
| 9 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |
