Buy or Renew
Buy or Renew

Network Security

Engage with peers and experts on network security topics such as FTD, FMC, FDM, CDO and ASA.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

“Join

 
Labels

Forum Posts

Start a conversation

Resolved! New ASA 5510 Setup help with NAT

Hi all,I am new to Cisco ASA devices.  I have some experience with Catalyst Switches and with the SA smaller security devices.  I have a new ASA 5510 and I am trying to use the ASDM GUI software to configure it.  I do have a USB to Serial cable thats...

Chris Ivy by • Level 1
  • 2041 Views
  • 5 replies
  • 0 Helpful votes

Resolved! ASA5505 as LAN router

I would like to use an ASA5505 as a simple LAN-to-LAN ethernet router.  My plan is to configure two interfaces with the same security level and then use the command that allows interfaces with the same security level to communicate with each other.  ...

tato386 by • Level 6
  • 654 Views
  • 5 replies
  • 0 Helpful votes

ASA with Implicit Rule

Hello All,I have a 5510 protecting a single MPLS site. I am trying to configure some new rules to allow traffic to flow into the ASA but looking at the logging everything is being denied by a implicit rule.How can I get past these implicit rules ?sam...

IrishMann by • Level 1
  • 11563 Views
  • 9 replies
  • 0 Helpful votes

command reference for IPS7

HelloWhen can i find command reference for IPS appliance ?i've found this link:http://www.cisco.com/en/US/docs/security/ips/7.0/command/reference/cmdref.htmlbut these are only system commands. I need all commans including signature/engine configurati...

Resolved! ASA 5510 7.2(3) - Access List Question

Greetings,     I'm running a Cisco ASA 5510 with version 7.2(3) and I've been tasked with permitting some inbound & outbound TCP & UDP ports to/from a specified address space on the internet.  I'm still a Cisco noob and all the training resources I'...

jwilson by • Level 1
  • 824 Views
  • 6 replies
  • 0 Helpful votes

Cisco IOS Firewall HA

I'm looking to use 2x 2901 Routers as firewalls on my network.Will this work? Will the configurations stay in sync? If not how do other people manage this?Or should I just buy  2x ASA 5510 and build active/standby

IOS CBFW firewall HA

Hi All,Have anyone deploy HA on IOS firewall with Fastethernet interface configured into multiple sub-interfaces and tag with different vlan-Id and is assign as inside interfaces. Serial interface is outside interface. Would like to know whether HA c...

Dual NAT

Hi, Dual NAT is configured on ASA. The configuration is as follows:- ====================== nat (outside) 4 access-list OUT-TO-SVR outside ! global (inside) 4 172.30.30.1 ! access-list OUT-TO-SVR extended permit ip any host 192.168.10.1 ! static (ins...

nicky0690 by • Level 1
  • 630 Views
  • 1 replies
  • 0 Helpful votes

Firewall clock change-->syslog message

Is there any way to log clock changes on PIX/ASA. In IOS there is message%SYS-6-CLOCKUPDATE: System clock has been updated fromBut i cant find that on PIX/ASAI know that i can log when user chage clock via comman prompt(logging commands) but i would ...

fmartic26 by • Level 1
  • 564 Views
  • 2 replies
  • 0 Helpful votes
View All
Review Cisco Networking for a $25 gift card