Hi Team,I have enabled the Port Scan in the ACP which is configurd for the RAVPN gateway, when I run the scan I am able to see the port 443 is opened but there is no logs in the Events. We are managin the FTD via FMC. I am new to Cisco FTD. I was a P...
Is there a way to do a factory reset on this FPR1010? The original problem I have is I can ping both 192.168.1.1 and .45.45 but I'm not able to reach the page via browser. "This site can not be reached" I'm able to communicate via USB console though...
Hi all. I'm trying to migrate an FMC-managed FTD 4125 HA pair to a pair of FTD 4215s. FMC and all of the FTDs are running 7.4.2.1. Is there any way to migrate the FTD interfaces, routing, etc over to the 4215s? I talked to the TAC and they told me ...
Hello , i have an ASA firewall ( 5525) and i want to configure a scheduled backup , is there any documentation about this please ?best regard
Hi, is it possible to set up FMC High Availability with one FMCv and one FMC Hardware Appliances.I can't find any official statement that rules this out. kind regards Alex
I am reading doc on Cisco FTD intrusion policy, can anyone explain to me what the difference is between Rule state and Rule action in Cisco FTD firewall intrusion policy?
Hi, I have a Site to Site VPN configuration on FTD 3110 version 7.6 managed by FMC. There is a subnet mentioned for protected network. Customer has a ask that they want to exclude some of the traffic to go via that tunnel if they are trying to reach ...
Hi AllI am aware of BGP flowspec, you have a server (flowspec controller) and clients which are the bgp neighbors to the controller?How does it actually work in practice? do all the ISP routers send netflow information to the controller and based on ...
I am trying to upgrade FXOS from 2.10 to 2.16 on 4100, I uploaded package as usual and clicked on upgrade. There was a message saying package is being unpacked and them a message about comaptibility with FTD instance running in the device. Accepted a...
Hey all, I currently have an HA pair of FTD 4145 running v7.6.2 When I run command "show failover state" I get a state of Sync Skipped - STANDBYCan anyone provide some clarification as to what this state means and why the sync was skipped? Has the H...
HiI have a static Route Based VPN and am wondering if I create a loopback interface on the FTD is there a way to allow this IP over the VPN to test the VPN or generate some traffic from the FTD across the VPN ?? Thanks
We receive this vulnerability on Cisco C9120AXI-E Access Point, Let me know if anyone has solution for this vulnerabilityCVE ID: CVE-2023-48795https://bst.cisco.com/bugsearch/bug/CSCwi61646?rfs=qvloginhttps://www.tenable.com/plugins/nessus/187315
Hi all,i Have FMCv on esxi version 7.2.4 connect with 2 FTD same version need to Replace the FMC to new one 1700 it`s version 7.4and after that i need to replace the two FTD with new ones 3100 serise -----i do this berfore but the FMC was 1600 to 170...
I upgraded from 7.0.8.1-4 to 7.0.8.2-2, the pre-check was OK but I encountered the following error in the log file: EXPORT ERROR: The source parameter ("/var/cisco/deploy/sandbox/snort3-pkg/usr/local/sf/bin/snort-75-3.1.0.800-9") did not pass the Typ...
Hi, I'll shortly have to deploy a physical firepower of the 4100 family "4115". I know that the first MGMT interface showing up is for chassis FXOS purpuses. In Cisco videos I've seen that the management interface used for FTD "logical instance" is t...
