I have the specified configurations on my 2821 routerinterface FastEthernet0/0 ip address 66.x.x.x 255.255.255.248 ip access-group INBOUND in no ip redirects ip nbar protocol-discovery ip inspect fw out speed 100 full-duplex service-policy inp...
I have the specified configurations on my 2821 routerinterface FastEthernet0/0 ip address 66.x.x.x 255.255.255.248 ip access-group INBOUND in no ip redirects ip nbar protocol-discovery ip inspect fw out speed 100 full-duplex service-policy inp...
Hello, I am configuring ASA as firewall+vpn, basically outside of appliance is T1 access(, there are 5 vlans in inside via a iptables, iptables's outside is on the same vlan as insdie of ASA (192.168.5.1 and 192.168.5.2). vpn users are authenticate...
When I tried to upload Signature Engine 4 file (IPS-engine-E4-req-7.0-2.pkg), using FTP server both by CLI and IDM, to new AIP SSM sensor, I got the following error message: Cannot upgrade software on the sensor - socket error:110.When I tried to d...
Hi folks,using ASA5520, I work for a Higher Ed campus. We have a public / guest wireless network for students to have access to internet only. I am currenlty blocking all ICMP from that network to my private network and receiving alot of deny hits fo...
Hi ..I have a subnet of 57.24.130.0/27i have two routers in that subnet ip'd as followed57.24.130.11 with a mac address of 001d.46c4.0c6057.24.130.12 with a mac address of 001c.f6f8.b570now in this subnet I also two PIX firewalls ver 8.0(4) with IP...
How do you convert a pix501 configuration to use on a sa520? I do not know how to use a GUI, I am a cli guy. Can a pix501 config be used on a sa520?
We have a new DSL provider in one of our remote hospital clinics. The old DSL provider had us configure our Pix using PPOE. The new provider does not use PPOE. I just wanted to know if someone could please let me know how to configure our Pix to wo...
Hi guys:I have a problem with my AIP-SSM, recently I download the latest license and I need to install in my AIP but when I try to do this I receive this error:"errSystemError-idsPackageMgr: digital signature of the update file was not valid, use CCO...
Hi, I talked with a "ciscoman" yesterday and according to him, te FWSM moduled will be announced "End-of-sale" in a few months and be replaced by the new module WSC-SVC-ASA-SM1-K9.Do anyone have any information about this new module for Cat 6500 ? ...
Dear All,Let's say I have an ISR 28xx or 38xx and I want to enable IOS Content Filtering.OK, I buy the subscribtion license like SL-CNFIL-XXX-1Y, where the XXX is depending on the platform.What would happen, if I want to transfer for example the 2811...
Hi.I have a Cisco 5520 with aim-ssm-10 and I need to recover the password or perform a factory reset.I have run hw-module module 1 password-reset and it has successfully reset the password, however previously the default Cisco username had been demot...
Hi,I'm having an issue on my Pix 501- ver. 6.3(5) firewall when host 192.168.1.2 accessing any website, no website is opening and when i issue command sh xlate so don't see anything and i think i must enable natting on this firewall as same as on ASA...
Hi,A customer network ist set up with 2 ASAs (both with v8.32) including asymmetric routing:Internet Remote Network (Server HTTPS)| || || ...
When configuring a static Rendezvous Point in the ASA (8.4(2) there is the option in ASDM to check "Generate IOS compatible register messages (Enable if your Rendezvous Point is an IOS router)."If the RP is an IOS router, and this box is NOT checked,...
Hello,I have a SSL certificate from a third party that is showing under the Identity in ADSM, howerver the audit scan of the firewall shows that the SSL Certificate Signed with an unknown certification Authority. I have installed the Intermediate Pri...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-26-2026 07:54 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM | ||
| 04-22-2026 11:56 AM |