Hi Guys,What does the following statement means on the pix firewall ? For exampleglobal (outside) 2 67.75.236.193-67.75.236.194 netmask 255.255.255.240Does the above mean that we have got two address 67.75.236.193 and 67.75.236.194 for the firewall t...
Hello,Here are the configs for failover:PRIMARYfailover lan unit primaryfailover lan interface failover GigabitEthernet0/3failover interface ip failover 192.168.3.1 255.255.255.0 standby 192.168.3.2failover link failover GigabitEthernet0/3failoverSEC...
Hi allI am trying to add a username to the local database for remote VPN connection but always i get this error when I addEncrypted password is of incorrect lengthUsername addition failed.Can you help me to solve this problem?ThanksMukundh
Hi,I could not find any information about traffic which is over declared IPS appliance performance (throughput) limit.Those packets will be droped or will pass through without inspection?Thanks in advance!Radim
I have an ASA5510 which was running version 8.31. SSH was working fine on version 8.31 but since i upgraded it to version 8.41 the SSH stopped working. I would appreciate if someone can help me?Thanks,Lake
I have one ASA 5520 up and runnign, with complete configuration (ssl customization, DAP, CSD...) with bunch of files on flash drive, etc. I am using software 8.3Now I received one 5520 that I want to use failover, it is with 8.3, I will make sure tha...
alright folks, i'm new with the asa's...i'm familiar with the FWSM's on 6500's and pix...I'm running Version 8.3(2) and i wanted to setup nat-control and use of identify nats for advertising inside subnets to my outside networks.the old command was s...
Hello,Is it possible to manage (via the ASDM) my ASA from a *inside* LAN to the *outside* interface? I know this might sound crazy but believe me, I have good reasons.Just to show you: inside if ...
Hello Friends,I have applied a static Nat for 1 of the server in DMZ interface , I have done proper static Nat and also given for port 80 traffic on outside access list,The strange thing is when i do capture on my outside interface for public IP i r...
Hi,can anyone guide me to configure ASA 5510 as belowinside users should communicate with Hosts on the DMZ Zone and at the same time they should go for internet towards outside interfaceASA with 8.3(1)default security levelsattached is the digram for...
hi all,i two 5550 firewall set up for redundance purpose . in failover we define two different ip add one for primary and one for secondary .exampleinterface Ethernet0/0 nameif outside security-level 0 ip address xxxx.0.0.0.1 255.255.255.0 standb...
Just wanted to know if someone could show me step-by-step how to configure SSH access on my PIX 506e. I would like to use local authentication with no AAA server. Also I would like to have telnet disabled completely. Thank you.Thomas
Hi everyone,I hope this is an easy one for all. I have a router on a stick setup going on and I would like to put a firewall into the picture. I have two VLANs - VLAN 2 and VLAN 3. VLAN 2 is in the 192.168.2.x network and trunks back to the router at...
I currently have an ASA 5510 unit. I have a dmz setup which house some web servers and an inside interface. The web servers contain multiple public ip addresses which I have natted and access is fine.What is the most simple way to enable ping for my ...
Hi all,I have a central site with few remotes sites connected this way: 1) A pair of Cisco ASA 5520 deployed in ACTIVE/PASSIVE redundancy at the edge of all sites including the central 2) ALL sites are interconnected by VSAT via the central...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-26-2026 07:54 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM | ||
| 04-22-2026 11:56 AM |
