Buy or Renew
Buy or Renew
Our Next Community Adventure Begins soon! Click to LEARN MORE.

Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

“Join

 
Labels

Forum Posts

Start a conversation

upgrading pix to 8.0

I have a pix 535 running 7.2 code and I'm trying to update it with 8.0 code and I get an error while doing it via the asdm:error occured in uploading the file:server returned HTTP response code: 413Any ideas?

esossamon by • Community Member
  • 968 Views
  • 3 replies
  • 0 Helpful votes

Resolved! ASA 5540/5520 Failover

Hello Experts,Just had a quick question regarding ASA failover:  Is it possible to have an ASA pair, with the primary ASA being a 5540 and the standby device an ASA 5520 (or vice versa)? I need to replace a set of ASA 5540s with with ASA 5520s on our...

Resolved! LOCAL Authnetication

I set the enable, http, and console authentication on an ASA5510 to LOCAL,but did not configure local users.  Now I can't log into it with the original crendentials.  Fortunately, I did not save the configuration to flash so I could always power-cycl...

pootboy69 by • Level 3
  • 1247 Views
  • 4 replies
  • 0 Helpful votes

Resolved! Close Port Cisco PIX 506E

                         If I add a Deny ACL after all my permit ACL's will a deny any source to port 500  close the port on my PIX 506? I need to keep that port from showing up in a scan to comply with security standards? Also this should not cause ...

Resolved! NAC Manager HA stop responding

Hi guys, I have 2 CAM working in failover. 3 times this failover had stopped responding sudenly. I couldn´t managed the device through the GUI o SSH. The two devices not responded. The only way to take the control back was restarting them. They have ...

gerardtorin by • Frequent Visitor
  • 1264 Views
  • 4 replies
  • 0 Helpful votes

Resolved! Updating Cisco IDS 4215 signatures

Hello people, we have some Cisco IDS 4215 and would like to know if upgrading the signatures we can remove those released previously or if the previous ones should not be eliminated.Following system information from one of these devices.***TAC Contac...

avvenk by • Level 1
  • 2040 Views
  • 3 replies
  • 0 Helpful votes

ICMP Stateful

Hi,Most of us knows that ICMP is not a stateful protocol, and we can make it using ICMP inspection in ASA.As per my understanding,In TCP, TCP Flags are making TCP capable of stateful protocol, In UDP, src and dst port numbers playing the role to make...

manuadoor by • Level 3
  • 3639 Views
  • 1 replies
  • 0 Helpful votes

ASA nat-control issue

We are looking for a clarification of ASA nat-control command. Unfortunately, we don't have spare device to test it out.The situation is as follows:An ASA firewall has three interfaces: "inside", "outside", and "corpinside".nat-control is DISABLED.A ...

lanli_ltp by • Community Member
  • 1744 Views
  • 5 replies
  • 0 Helpful votes

Resolved! Telnet garbled on smtp port via ASA

Hi folks,I am experiencing garbled telnet sessions on port 25 to ms-exchange servers on the other side of an ASA5520.This is an MS "basic check" for inter-server email comms, but is proving problematic.SMTP is permitted through the ASA.Suggestions we...

a.whiting by • Level 2
  • 2124 Views
  • 3 replies
  • 0 Helpful votes
Load more
Review Cisco Networking for a $25 gift card