Hello, I need some help getting my ASDM working again.For some reason when I try used ASDM I can't get pass the authenticate part. When I try to ssh to the same firewall using the same username and password worked fine no issue.ASDM version 712-102 A...
We've had LDAP integration into our AD for many years for authentication into the FMC and FTD. However, we're trying to setup a rule, so that someone in our finance department is the only one who can get access to a particular website. When I configu...
I have a question about FP sizing.For a site that has approximately 2000 active connections through an ASA5506x (not running any firepower just classic ASA, output of "show conn") would a FP1010 be powerful enough to run all three FTD licenses?
We have a Cisco FirePower FTD 2140. When I go to MONITOR-EVENTS, I'd like to see the "ORIGINAL CLIENT COUNTRY AND CONTINENT" within the filtered session. Presently, it is blank, as if it does not know or there is a setting missing somewhere to allo...
Hello,I have successfully register FTD to remote FMC.1-FMC ---> FTD--->NATIP_FMC and PORT 8305 ----> REMOTE FTD-PUBLIC IPCreated ACL only access from FTD-RemoteCreated VPN/S2S between both FTD.Now my problem is how to convert the mgmt interface in pr...
Hi All,I have upgrade my FMC from 7.0.4 to 7.3.0 and right after the upgrade completes i get this Smart License Monitor Error and when i tried syncing my FMC to the license portal it just synchs properly and i am just wondering what make this error w...
My system uses a server as a PDC, at the user side I set the DNS for the computer as the IP of the PDC, sometimes I find that my firewall device does not detect which website is being accessed by any computer. internally, I only found out that my ser...
I can't think of a reason why the Gateway firewall would be logging Inside to Inside as shown in the below. Any ideas why I would be seeing these logs for same subnet traffic flows on a gateway firewall? In screenshot you cant really see but it does ...
Hi to all,How may I visualize the list of Feeds on Cisco FMC in Objects -->Security Intelligence-->Network List and Feeds? I am calling the list of Feeds on FMC by third-party Software and I am unable to view the list of feeds anywhere however I am a...
Hello Guys, I am getting the following error message while trying to create 'Remote Storage Device' type NFS in FMC version 6.1 . My NFS is running on windows 2012 server and during testing i do see a file name "sf-remote-storage_test.txt" created in...
Hi all, We plan to implement IPSec VTI on FTD2120 on HA Pair.As I can see, IPSec VTI is not supported on cluster:https://www.cisco.com/c/en/us/support/docs/security-vpn/ipsec-negotiation-ike-protocols/216276-configure-route-based-site-to-site-vpn-t.h...
In the morning my system was warned that the drive was about to be full, after looking for the cause I found that there was a rather large file that took up 64Gb, I tried for the system not to take any log in and out. of the system user but it doesn'...
I'm trying out ASAv RA-VPN on AWS https://aws.amazon.com/solutions/partners/cisco-asav-ravpnHow can I get a license for downloading the software packages to complete the RA-VPN configuration to actual try it? Using the serial number from the deployed...
Hi All What will be the Throughput speed of NGFW 4110 with Advance malware protection + Firewall Threat Protection (IPS) Install on the ApplianceWhat will be the Throughput speed of NGFW 4110 with Firewall Threat Protection (IPS) Install on the Appli...
Firepower 1010 v6.6 When I try to browse to management ip I assigned it worked for one day and then the next it did not work no more. So I factory reset it follow the Cisco white pages and now I can’t get back in the firewall now. When type /show int...
