Hello - I tried tackling this before when I had a PIX 515 and never got it to work. Now we have replaced the 515 with an ASA 5520 and I still can not get it to work. Here is the issue. I have a 15Mb Verizon FIOS (fiber - hand off ethernet). I have th...
Dear all, We are running a very critical setup , using Cisco 6509 switches.I want to schedule NAM (Network analysis Module) to send or make remote storage to a server on the network. (ftp services are running on the server)I tried to configure ftp on...
We purchased a FWSM and external IPS 4255 to replace our existing external PIX525 and another vendors IPS. We currently have a 1 gig uplink to our main campus and the Internet. The PIX sits out front with the IPS behind it then our core 6513 campus r...
Hi all,Help for a newbie please.I have a problem with the inside network accessing web servers in the DMZ. I am getting portmap translation fail errors, however I need help with the command to allow all inside hosts access to the DMZ. It's a new fire...
Just getting started with FWSM. IT is currently running version 2.3(4) with device manager 4.1(5). Is it ok to move up to version 4.X?If so note for version 4.X say you need to be at maintenance software Release 2.1(2)or higher. It appears that 2.1(4...
I`m trying to verify some information but can find nothing of use on the cisco.com website or google. So, I turn to you guys/gals.An associate in another business unit has purchased a few ASA 5580's and was told if he were to run multiple security co...
What is needed to set up a CA in PIX. What are the requirements for setting such a CA?Thank you.
I have a 5520 running 7.2(4) (Routed, single context) with an SSM20 running 6.1(1)E2.I am struggling a bit with the SSM setup on my 5520. I have created 2 service policies, one applied to a DMZ interface and configured as "in-line". The other applied...
Our exchange folks are moving to 2007. They are trying to put up new edge servers and have asked for outside addresses for the edge servers. Problem is that they want to source IP to be the same address as the NAT. Below is an example of the NAT. Wha...
I've noticed that when randow-seq is enabled, about 10% connections failed.I've encountered the same effect on version 2.3 and 3.2.Any suggestion about what could be the causes of such behaviour ?Frans
Hi,I'm currently seeing interface ethernet2 on my pix 515e as Admin Down, Line Protocol Up.Could someone pls explain why a PIX does this?? Is it just because its detecting layer 2 connectivity??
I am new to firewalling and have a PIX501 that has been setup and running for awhile now without any problems. But I now need to get the PIX to allow a new port number through. How do I do this?I tried adding:access-list 101 permit tcp any host xxx.x...
Hi all. How do i implement ips on my asa5510? I can't seem to be able to find any website on this. Can i know if any of you find that the ips is effective? I am using asa ver7.2 and asdm5.2. Pls advise. Thks in advance.
I 2 6506 switches, that are configured as Active/Standby. but the problem I am facing is that the running config on both FWSM are in Sync on both FWSM, the startup config on the active is the same as the running, but the startup config on the Standby...
Dear all, kindly can you exlain what is the security hole in this message%SVCLC-5-FWTRUNK: Firewalled VLANs configured on trunks
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 06-24-2026 08:00 AM | ||
| 05-26-2026 07:54 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM |
| User | Count |
|---|---|
| 5 | |
| 1 | |
| 1 | |
| 1 | |
| 1 |
