We have a pix firewalling a small lab in our company with the outside interface connected to one of our local lan's.Other than setting telnet 192.168.x.x 255.255.0.0 outside , is there anything else that is required?---Mike
We have a pix firewalling a small lab in our company with the outside interface connected to one of our local lan's.Other than setting telnet 192.168.x.x 255.255.0.0 outside , is there anything else that is required?---Mike
We are running a Cisco ASA 5505 and remote clients are 871's. We currently use a EasyVPN configuration between the single ASA and our 13 871's. Today (1) out of the (13) tunnels is experiencing packet loss. I have power cycles the broadband router ...
ASA 5510 v8.0(3)Anyconnect v2.2Pretty simple setup, just a single group policy that has the Idle timeout set to 60 minutes.Testing it out, I connect with the anyconnect client and I can see session via the ASDM monitoring section and watch as the idl...
I have another problem that I just encountered after getting NAT set up correctly. I posted yesterday about a problem with using 2 WAN interfaces, once I got it all set up and working, now the inside static clients don't resolve hostnames, only IPs,...
Input to the outside interface is maxed and has been for about an hour. I need help tracing either the source or destiniation so I can take preventative measures if necessary.I'm not very good at filtering the log! :(
Dear sir,i have tipical problem is i have two servers connected to unmanagble switch and from that switch to connected to one of of the port eth0/0 and i taken output eth0/1 and i conncted to my pc through the firewall i want to access my serversthro...
We are using ASA 5510 with AIP-SSM 10 that having IPS Version 6.0(3)E1 with a valid licensee agreement. Now we want to update IPS version to 6.1(1)E2, is the update is possible? If yes guide me how, and also guide me or provide the link how to backup...
I have a ASA 5505 with an inside netowk of 10.xx.180.0, and an outside network of xxx.xxx.23.170. Now the ouside server has to be bale to printer to a printer on the inside for daily reports. should I just nat the inside IP to the a outside IP.What ...
I have two remote vpn subnets that need to communicate. I have my access list as access-list No-NAT extended permit ip 172.16.140.0 255.255.255.0 172.18.3.0 255.255.255.0, however this does not seem to do the trick. Could these VPN's be terminating...
I have an ASA 5520 with 4GE SSM module.In the ASDM, I see the basic IPS signatures...anyway to upgrade these signatures, add to them, etc?
My ASA 5505 has a static IP address that is connected directly to the internet.Behind the ASA 5505 is my web server that is connected to theinternal network.I would like to forward the http traffic that hits ASA 5505 to the internal web Server. I ha...
Hi,Currently I do not have a license on my IDS 4200 series box.I will get a trial license , and want to upgrade the signatures .What is the way to download the signatures to the IPS box Thanks in advance Raj
I hope that I am describing my issue correctly:I am getting errors that incoming packets are dropped because of access list "outside_access_in"But I can't for the life of me figure it out.I am pretty sure this used to work.For example we use netmotio...
I cant ping anything on the inside interface of a pix 515 from a VPN client.
HiOn 4.1.3.2 and went to http://www.nessus.org/download/index.phpand downloadnessus-plugins-2.2.11.tar.gz (7468 KB)nessus-plugins-GPL-2.2.11.tar.gz (1071 KB)renamed the 1st one to "plugins.tar.gz" and was able to upload the plugin successfully but wh...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-16-2025 04:21 AM | ||
07-06-2025 01:40 PM | ||
07-04-2025 01:59 AM | ||
06-19-2025 07:32 AM | ||
06-17-2025 01:07 PM |
User | Count |
---|---|
7 | |
6 | |
5 | |
3 | |
1 |