Buy or Renew
Buy or Renew

Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

“Join

 
Labels

Forum Posts

Start a conversation

Resolved! SSM IPS blocking via ASA

I have set up my ASA asa a blocking device in my ssm10. That part works fine. The problem is I had defined local networks in the "Never block Addresses" configuration box. Before long, the ASA had in fact shunned an address which was part of that "ne...

acomiskey by • Level 10
  • 727 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Pix 515E second internal IP address

Hi everyone quick question how do you configure another ip address on a pix? I already have an in and out what I was looking to do is add another in address. I tried just doing: ip address inside 192.168.50.25 255.255.255.0 but ended up changing my ...

wgranada1 by • Level 1
  • 1806 Views
  • 6 replies
  • 0 Helpful votes

VPN 'show commands' on PIX 6.3

Hello, have a simple question. I'm new to PIX 6.3 and have to be troubleshooting a site to site vpn tunnel terminating on pix on my end. Can someone tell me some show comamnds that work in 6.3? 6.3 isn't that user friendly!!!Thanks,Jason

jaye15394 by • Level 1
  • 723 Views
  • 2 replies
  • 0 Helpful votes

Designing ASA Firewall

Hi,I need to desing the outer firewall for my company. Now i'm doubting about the design and about the product choice.The situation is We have a provider equipment facilitation 2 ports at the inside. One for internet and one for our brache offices....

Resolved! is this NAT config possible o a PIX515e?

i have been asked if it's possible to have inside users (172.16.1.1) who have a dns entry pointing them to our outside interface (1.2.3.4) for our web site company.net to be rerouted to our dmz which is 10.10.5.0 with out going out of the PIX and bac...

static nat

Is there a way to map 2 different inside addresses to a common outside address via a static nat command. Other firewalls I have worked with, particularly Netscreen, allows me to create two mapped addresses to the same host. I am trying to achieve sam...

alackraj by • Level 1
  • 394 Views
  • 1 replies
  • 0 Helpful votes

Help with intermittent ASA 5510 problem

Our network has been experiencing intermittent issues the last few days. At random times, the network becomes unstable, voip, citrix connections to servers, connections to the internet, vpn connections, etc;.I started watching the logging on the ASA...

rweales01 by • Level 1
  • 611 Views
  • 2 replies
  • 0 Helpful votes

Resolved! No Internet From Inside

Hello - I have just had to replace a dead (finally) PIX 520. Untill my company can afford it, I am using a PIX 501. The outside interface is connected to a Verizon DSL router, and the inside through a 2950 and an old 1600 series router. Problem is...

Resolved! ASA ASDM connection problems

Hi,I'm new to ASA and have a question about what alternatives there is to manage the ASA "out of the box".My problem is that after uppgrading ASDM to 6.0(3) I get the following error message:"Your ASA Image has a version number 7.2(2) which is not su...

Cisco ASA5520 failover trigger

I have problem with the ASA firewalls failover, when the ether channel between the layer 2 switches are pulled out, this triggers failover on the ASA, the ASA are Active/Standby. Please see the attached file for the real architecture this is in visio...

Load more
Review Cisco Networking for a $25 gift card