Network Security

Hello everyone,I just completed a signature update to S307.0 on the ASA-SSM-10 and I noticed that the virus Update has the following...Virus Update V1.2 2005-11-24Does anyone know how I go about updating the Virus Update?I can't seem to find any info...

I have a hand full of agents that stopped checking into the console with:[2007-10-12 12:16:29.630] [PID=388] [Csamanager]: inquire_config_status: Inquiring config status [37] with server server.domain.com, Failure (1), (elapsed_time=107825 ms)[2007-1...

Hi friends.I am new in cisco ... I entered to a enterprise who has 3 IDS 4250 ** , this devices doesn't have configurated ...and the signs are from 2005 !!!Cisco Systems Intrusion Detection Sensor, Version 4.1(5)S201MainApp 2005_Sep_01_21.30 (Release...

Out Cisco Pix 515 has been fine for months/years on the CPU since the last week. The average has always been 10%-20% until the beginning of October where it's hit 90%-100%, what steps do I need to take first?

I'm preparing for a disaster recovery design.I'm thinking to use the lan failover for my PIX firewall.Some suggestions?Thanks.Andrea

How can I tell what a PIX is going to Proxy ARP for. Is there a command I can use to easily determine this, or do I need to look through the config and manually work out what the PIX will Proxy ARP for? Thanks.

I have host using a private internal IP that will only talk to machines on the same private IP. I need to have public IPs talk to this machine. I have a PIX that uses the same private IP subnet on its inside interface. What I would like to do is a PA...

Hello, I am trying to configure my ASA5505 to correctly bypass the stateful inspection for UDP port 15044. Currently none of the default-inspect polices do not have this port listed. How do I add it and correctly get the VOIP traffic to not be inspec...

I have a PIX 515E w/ 7.0. We have a Wireless network that is associated with its own interface. We have 3 interfaces: INET, LAN and WIRELESS. There are no DNS servers on this network and clients perform DNS lookups to the Internet provider's servers....

Hi, we have a ASA5540 configured with up to 25 VLANs. Now we want to limit 10 VLANs with 100 MBit/s for each VLAN. These VLANs are on the same physical link.How can this be configured? Have anyone doing this before, or have you any documentation with...

I Have a PIX 515 6.3(5). I need to allow outside web access to a host from the outside; opening ports 9000-9005. Here is an example of the code, that I have come up with. Is there a better way to write this (e.g. One statement with a range of ports v...

How can I migrate from a pix firewall to a ASA firewall using the same DMZ. doing this so there will be no changes to the ip's in the DMZ. I have tried to NAT the inbound DMZ of the ASA which gives the ASA's IP addres to internal DMZ servers. Works a...

Hello,From which PIX OS version is it possible to assign a /31 address mask to an interface? In version 6.3(4) if I try to assign an IP with subnet mask 255.255.255.254 I get the error:"Warning : IP and subnetmask form invalid pair indicating broadca...

The boot sequence stop at this point:CISCO SYSTEMS PIX FIREWALL Embedded BIOS Version 4.3.207 01/02/02 16:12:22.73 Compiled by morlee 128 MB RAM PCI Device Table. Bus Dev Func VendID DevID Class Irq 00 00 00 8086 7192 Host Bridge 00 07 00 8086 7110 I...

Dear all,I have Pix 520(6.3(3)) and i'd like to replace it with another one PIX525 (7.0 or 7.2(2)) But the problem is in the old config ( Conduit ,Fixup,interfaces , VPN and...)how can i convert (move) the old config (6.3(3)) to the new one (7.2(2) o...