Hi All,We have a pair of FTD 3140s in HA that are deployed across different buildings within our campus that connect across two core switches with core 1 in the same building as FTD1 and core 2 in the same building as FTD2. FTD1 connects to core 1 us...
Forum Posts
We keep seeing this on Our FPR1120 running ASA 9.14.22.2 version. Also, our Device keeps hanging every 7 days and we have to reboot the device.Is it due to this above error? Any help would be appreciated.
I have FPR-2120, currently running ASA 9.10(1)11, when I try to upgrade it, I am getting %ERROR: Signature not valid for file disk0:/cisco-asa-fp2k.9.16.4.SPA. Below is my asdm and fxos version. Any help would be greatly appreciated. Been troubleshoo...
Hi, I still don´t fully understand the licensing in relation to Cisco ASA Firepower Licensing. I already asked a question regarding the FMC here: https://supportforums.cisco.com/discussion/13086371/firesight-license-60-not-needed. I learned, that for...
Hi,in FMC 7.4.3 we use Admin external auth with Active Directory (LDAPs).AD Admin says FMC uses NTLM and we have to change to Kerberos.I can't find Kerberos mentioned in FMC Admin documentation.Is it possible to change to Kerberos?regards,Thomas
I have a dhcp relay set up for my inside interface. I also have subinterface on another interface in routed mode that is on a separate security zone and separate network that also needs to point to the same dhcp relay server. On an old pair of ASAa I...
Resolved! ASA 9.14.4.24
ASA 9.14.4.24: https://software.cisco.com/download/home/284143129/type/280775065/release/9.14.4%20Interim
I have a firewall that is managed via its own interface NOT the FDM software. I need to get the configuration from it to FMC to I can use FMC to manage the firewall.I've seen posts that say I have to do it all manually to the Cisco Migration tool can...
Hello, We have a pair of FTD2130 behind a pair of routers (border routers for the campus, running BGP). This is Campus A (main campus).The topology is described briefly below:The FTD pair (running v7.2.10.2) is in Active-Standby mode; it serves as Fi...
We have cisco ASA device which are mentioned below and as requested we are sharing the below serial number and provide us the stable and recommended version to upgrade. Device model ASA 5516-X Cisco Adaptive Security Appliance Software Version 9.9(2)...
I have an air-gapped system that has the following (relevant) devices:2 x Cisco vFMC 300 running 7.6.0 build 113 running as an HA pair1 x Cisco SSM On-Prem running 9-202502I am trying to register the FMC to the SSM but it is consistently failing to r...
Hi team. Does anyone know what the story is with vDP on the 4200 series? In CCW you can order vDP as a feature license on the 4100 series platforms, but not on the 4200 series. Given that the 4200 is the recommended replacement for the soon-to-be-...
After upgrading the FMC 4600 to version 7.6.2, an error appeared related to connectivity with Cisco Cloud. TAC recommended a workaround by enabling Cisco Success Network. Approximately 24 hours later, the initial error cleared; however, a new error a...
Hi to all,i am wondering if i can configure FTD with loose RPF instead of strict RPF which (i suppose) that is currently running.I am getting a whole lot of syslog messages with id 106016: Deny IP spoof from (194.x.y.z) to "My GW IP" on interface vla...
Resolved! FTD Etherchannel/LACP question
Hello, I have a FTD 1010 in my home lab that's using 1 routed interface for outside and the rest of the interfaces are used as switchports on a VLAN that I use for the Inside. Now I also have a Synology NAS with two interfaces that can be bond toge...
