Hello, I have an FPR 1150 with FTD 6.6.1 managed locally(FDM)Does it support SNMP configuration?Is there a guide? Thanks and regards, Konstantinos
Hello, I have an FPR 1150 with FTD 6.6.1 managed locally(FDM)Does it support SNMP configuration?Is there a guide? Thanks and regards, Konstantinos
Hi, I'm looking to configure rules on an FTD firewall to allow CAPWAP wireless traffic between Wireless Access Points and Wireless Access Controllers. CAPWAP uses UDP ports 5246 & 5247 to encapsulate the wireless data. I believe CAPWAP works in a s...
Hi all Setting up Anyconnect from scratch on the firepowers. Using the FMC. How do i remove the old protocols like TLS1.0 and TLS 1.1 from being used. I cant see that in the anyconnect setup ?Is this done at the interface level ? Any help would be gr...
Hello, I have a general question regarding an older Cisco ASA 5585 I'm looking through the configuration on that's running ASA version 9.8(4)25, and was wondering if anyone could help. In the interface configuration, do ports fail into a closed state...
- FYI : https://www.cisco.com/c/en/us/support/docs/field-notices/722/fn72282.html M.
I have an ASA 5516x connected to a Layer 3 (3850x) switch with multiple interfaces (Inside, Guest) and a connection to a 3850 where I have VLANs, and IP Routing enabled. Not to be able to reach the internet from any of these VLANs. I'm able to ping ...
Hi I'm looking for some help. We have deployed both Client VPNs for Remote access by Staff and WebVPNs for support access by 3rd parties on the same ASA. We are using Aliases as a method of 3rd parties to choose their "profile". However we have notic...
Dear All I want to integrate TrendMicro Deep Discovery Inspector (monitor all network ports) with Cisco ACI. So that all network traffic of ACI can be monitored by TrendMicro Deep Discovery Inspector(DDI). Anyone can help or has exprience using Tren...
Hi We have a router and do not know why we started to receive security warning. Below is the info we received. Now it has ip https enable and http disabled. If we disable the https, it should resolve the issue? Any other solutions? Thanks SSL Versio...
FMC 4500 appliance set to auto download and install Geo location updates. Task notifications keep stating that the download and install were successful but the FMC file in use is not the same as the "installed" version. FMC continuously attempts to...
Dear Community, I was noticing that all of the timestamps for the syslogs coming from my FTD devices and being sent to my syslog servers are in UTC time zone. Is there a way to change the timezone in the FTDs so the logs in my syslog server will refl...
Hello community, I have created a ipsec with two ASA both location having 2 ISP link. I have down NAT for both side. what command need to put on both firewall that will activate failover. once primary ISP down them secondary.should be up.. Sumy,
We are currently backing up FMC and FTD's daily and have been for about 3 years. Fortunately, we've not had to restore due to a failure, but we have done restores just to check things out. We would like to go through the entire process in a lab where...
Hello Champs,Can we secure SF300 and SG300 Switches with F/W ver 1.4.11.5 using SHA-2 against weak KEX and MAC algorithms ?What are the commands to execute ?If this can not be done for SHA-2, Can we secure SF300-24 Switch with F/W ver 1.4.11.5 using ...
hey folks does anyone know we running FTD 6.3 FMC 6.3 and trying to create a certificate DN for authentication is the possible? Thank you.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-05-2026 09:59 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM | ||
| 04-22-2026 11:56 AM |
| User | Count |
|---|---|
| 9 | |
| 2 | |
| 2 | |
| 1 | |
| 1 |