Network Security

hi,our internet line to internet is all day at 100% trafic on outside interface /somebody is downloading some big files/. can I find out who is it? I tried set up log, syslog /kiwi/, etc., but there are too many messages.I need find out WHO is downlo...

Hi, this i have battled for days(firdt time user), i know it should be easy, but it isn't working. I have a pix 501 6.3(4). I need to enable an outside user connect to my server (using pcAnywhere). if my inside ip is a.b.c.d and my outside ip is e.f....

Hi there,We have a PIX 501 with PIX v.6.3(4) and PDM 3.0(3). Our vendor/consultant did not give as the IOS CD. We fired them a while ago and our maintenance contract has expired since.I'd like to create a backup CD for our PIX 501. How do I copy the ...

Dear All, one of my pix accessible through ssh. but im unable to ping the device. any thoughts..Thanks in advanceNataraj

Does anyone have a sample config for a PIX that is configured for an EzVPN tunnel configuration to a 3060? I already have IOS EzVPN tunnels online and operating very well, but now I'd like to test the PIX.

Hi,My company has got FR connection between H.O and its 4 B.O.In H.O there is 2 FR routers. I one H.O FR router there 3 PVC and in another H.O FR router only one PVC is there.The problem is that the connection is very slow between H.O and B.O thru FR...

based on Cisco website, a PIX 515e firewall running 6.3 can have maximum 10 interfaces, 6 physical interfaces, & 8 logical interfaces.Am i corect to say that the maximum 10 interfaces is a combination of physical & logical interfaces? I thought you ...

I'm trying to migrate from DES to AES and my net has PIX 506E, 515 and 535. When the VPN is estabilished between 515-506E both side can initialize it. But between 535-506E only the 506E initialize the VPN.If I return to DES the VPN works ok. Is it co...

Hello..Is it possible to configure site to site VPN between Router & PIX through VMS...??Details of VMS 2.2 (basic):1.ROUTER MC 1.2.12.PIX MC 1.2.2If its possible plz share your opinions.HTHRgds.,Sachin

I have a PIX 515-E w/ver. 6.2(2) (asking for a new one for x-mas) - the configuration I inherited included statics and conduits. Yes, I know I'm supposed to convert these to ACL's but unfortunately, I can't get the ok for the down time.Meanwhile, we...

Hello everyoneI have just upgraded one of my Pix to V7 and discover ASDM ,)Now i start to check the logs for potential problems.It's quite difficult because i'm flooded with BroadcastErrors from PC on my inside Zone ....710003 errors saying UDP acces...

We have recently installed a couple of PIX and I want our management station to ping the route on the outside of the PIX.I setup a rule to allow ICMP from the NMS to the router and then a echo reply from the route to the NMS but it does not seem to w...

Hi All,I have PIX 515 UR bundle running 6.3(3) in a failover setup.I have over 50 IPSec VPN tunnels,web traffic,NAT going through it and the memory used is around 60MB out of 128MB.I now have a new PIX 515E in test setup running 6.3(4) and Restricted...

Hi,I have problems sending mail to certain domains such as AOL, the mails are bouncing back as the ISP is carrying out a reverse dns lookup, I have a reverse record setup correctly.I have configurd a static transltion as shown below but when the mail...

I read that since CSA version 4.5 it is possible to apply policies based on system states. For this CSA policies can use information from the Cisco Trust Agent as a ‘state’ element.My question is now: What do I have to install additionally to the CSA...