Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Has anybody deployed dmvpn with vrf forwarding?I can not get eigrp working under the address family.For example:interface Tunnel10 ip vrf forwarding SDPI ip address 206.200.167.1 255.255.255.0 no ip redirects ip mtu 1300 ip nhrp map multicast dynamic...

cconte by • Community Member
  • 1153 Views
  • 2 replies
  • 0 Helpful votes

trying to use static (inside,outside) and access list to make use of aditional ip.access-list acl_out permit icmp any any echo-reply access-list acl_out permit icmp any any unreachable access-list acl_out permit icmp any any time-exceeded access-list...

jasonbegley by • Frequent Visitor
  • 1230 Views
  • 6 replies
  • 0 Helpful votes

I am having an issue with my pix stopping traffic between inside to DMZ web server. Normally, I can get from an inside computer to the web server in the DMZ. Then all of a sudden it stops. The PC's can no longer get to the web server. I have to go to...

dwilkes by • Community Member
  • 1154 Views
  • 6 replies
  • 0 Helpful votes

Anyone heard of a restricted license on the switch interfaces of a 501? I have a customer that can only access 2 of the 4 switch ports? As far as I know, the 501 only comes with user based licenses. Any ideas?Cisco PIX Firewall Version 6.3(3)134Cisco...

jjohann63 by • Community Member
  • 1254 Views
  • 4 replies
  • 0 Helpful votes

HiWe are migrating from Checkpoint to PIX. We have inside, outside, and DMZ interfaces. On the DMZ, we will have web servers with private addresses, the outside world connects to these servers through statics on the PIX.We currently have the CP in pl...

I had enabled timestamp by the follow commands.clock set 14:25:00 apr 1 2000logging timestampbut when i use sh log command to view the log,there is no timestamps:302015: Built inbound UDP connection -540117333 for outside:10.0.0.1/64911(10.1.1.1/6490...

xuan.z by • Community Member
  • 832 Views
  • 2 replies
  • 0 Helpful votes

When the secondary is active, the primary answers for the shared mac-address, this should not be the case. The switches get confused and intermitten problems occur. This only happens on the outside interface.Any suggestions

I currently have two problems with my setup. They may be connected but not sure.1. The outside link on the firewall will not reapond to and requests. I know that the exgternal connection is working but nothing is communicating. The internal network i...

hardypeter by • Community Member
  • 1611 Views
  • 7 replies
  • 0 Helpful votes

I am in the process of setting up VMS and have noticed that with every 'save and deploy' that I do, that all of my Pix's (which run VPN's) are given the following commands:‘no crypto map x interface outside’‘crypto map x 20 set security-association l...

pkinzel by • Community Member
  • 1113 Views
  • 2 replies
  • 0 Helpful votes

I'm running a PIX 501 from my primary office location running NAT. I'm trying to connect to a ConnectEnterprise Secure FTP destination. Because I have no previous experience configuring a PIX to work with a FTPS server, I was hoping for some help. Be...

Could someone please tell me what I'm missing here. We've ordered a 50 user upgrade for our PIX 501. What I received was an email with a 6 digit 'Digital License Agreement Number'. How do I apply that to the PIX? I thought maybe the activation-key co...

s.wilmes by • Community Member
  • 965 Views
  • 3 replies
  • 0 Helpful votes

I am looking for any reference for the various log messages generated by the VPN Concentrator hardware. Is there such a document.Something like what can be found at:http://www.cisco.com/en/US/products/sw/secursw/ps2120/products_system_message_guides_...

Hi,Is it possible to restrict traffic types over a site to site vpn with PIX. I am looking to restrict traffic to smtp, ping and pop3.I have the vpn working at the moment, but every time I change the access-list it stops working! I have also tried ap...

Hi, does someone know how to map ports on a PIX.Session started from "Outside" on 1812 response received on 1647 from RADIUS server on "inside" which needs to be mapped back to 1812 and delivered to originator.ThanksMick

mrrussell by • Level 2
  • 447 Views
  • 1 replies
  • 0 Helpful votes

HelloI need to convert 2 PIX Firewalls, one from restricted to unrestricted and the other from restricted to failover, then have them run as a pair, does anyone know if PIX-515-SW-FO is the correct product to use on the secondary?Many thanks Tony

tholmes by • Level 4
  • 2219 Views
  • 10 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card