I have a Site to Site VPN setup from an ASA 5510 (ASA Code) to an ASA 1010 (Without FMC); we are using the FDM GUI to manage this. The Site to Site VPN is working fine!I'm trying to open the HTTPS FDM GUI over the site-to-site VPN.ASA5510 192.168.24....
Forum Posts
Is this supposed to happen? I was upgrading the ASA5585-SSP-SFR20 FirePower module from v6.1 to v6.4 via FMC. I expected the SFR20 module to reboot but instead, the entire chassis rebooted. So basically, both my FirePower ASA5585-SSP-SFR20 module an...
I am receiving PAT pool exhausted messages after about 10-20 days uptime. (x.x.x.x is the public IP address of the device.)show xlate:UDP PAT from inside: 10.111.27.82/57362 to outside: x.x.x.x(external IP address)/57362 flags ri idle 68:36:09 timeou...
Hi,this morning I found in my FMC that some intrusion events are shown as "pass" instead of being dropped.I find this in my FMC under Analysis -> Intrusion Events -> Table view.example:2022-02-26 06:45:38low Pass xx.xx.xx.xx USA xx.xx.xx.xx USA3...
I have a Site to Site VPN setup from an ASA 5510 (ASA Code) to an ASA 1010 (Without FMC); we are using the FDM GUI to manage this. The Site to Site VPN is working fine, but we cannot ping from behind the ASA5510 to the inside interface of the ASA 101...
So I have a ASA 5555. On it I have directly connected interfaces going out to customers. Well one customer wants to be able to talk to another to share information and resources. I thought cool no problem I go into the ASDM allows each zone to talk ...
Hello, Has anyone been able to connect their FMC to a Synology NAS via NFS? I get errors (obvisouly, it's why I'm here) as seen in the pic below. I have been able to connect NFS to a different Ubuntu server so I know they Synology can do it. Please s...
Resolved! Cisco ASA/Firepower throughput per flow
Hello, what ist the throughput per throughput on multicore ASA Cisco ASA ASA5585-SSP-20 1 CPU 8 Core when using 10Gbit NICs ? Each flow is handled by one core. Is there a limit per core ? thanks
I have a system inside my network that we use to test Multicast sessions between my network and other sites. When I start it I can see incoming connections but nothing sending. I looked in the log and found the following errors on the ASA5525x ver...
Good Day We are planning an upgrade of the IMC Cisco Firepower Management centre.Can we upgrade the cisco IMC 2.0(13e) directly to 4.1(f) or any intermediate version? is any guide available with the steps to reimage the Cisco FMC through Cisco IMC C...
I have the L-FPR1000-ASA license and I'm not sure that I can reimage the FPR1010 to FTD and managed it locally with FDM.
Hello everyone! I'm having trouble recognizing the USB on the FTD 2110. My intention is to use it to re-image the ASA. I've formatted the flash drive to FAT32 a few times and the USB is not recognized on it. Do you have any tips to solve this problem...
Hi, I have a router on a stick configuration. Pfsense acts as the main router and the SG350 Cisco switch on L2 mode. Everything works fine regarding the current configuration. The addition I want to do is to isolate all my guests coming from an Acce...
I have 2 FMC devices in a HA pair. They are currently running 6.1.0.6 and I am looking to update them to 6.4.0 before upgrading them further to the latest release.The 'upgrade readiness check' does not work from the GUI even when the HA is in a pause...
Hi friendsMy question may seem a little simple!I've configured my asr 1002-x router for web-based authentication (Authentication Proxy).but whenever I type router's IP address in browser, the webui page appears and I don't see the authentication prox...
