Hi all,is possibile give more IP address to inside Ethernet interface?If yes, how to do this?Tks.
Hi all,is possibile give more IP address to inside Ethernet interface?If yes, how to do this?Tks.
PIX501-----internet-----PIX525 6.3 VPN 6.2I'm unable to sucessfully copy the running config from the 501 via the EZ-Vpn link to a tftp server on the core network.The client PC's on the SOHO network can access the internal netowrks (RF...
I have a a machine on the LAN the needs access to a web server which is also located on the LAN. The web server is ALSO available to the outside interface on the IP address assigned to that interface.I need to allow a machine on the LAN to access the...
when i do a sho int i can see my e0 and e1 but icannot see the other four int on my quad card..what do i do to see those int to config them?thanks.....
Hello,i would ask how could i verify the CPU usage on a PIX firewall 520 running software 5.1(4)?Thanks in advance Jacob.
My company does web development under asp.net. After putting everything behind the pix 515E there local iis (on there local machines) can no longer see the sql server. So this means when the run a local webpage that attempt to connect to the sql serv...
I know this is a simple questions but I cannot find the answer in cco. How do you clear the interface counters? How do you set the duplex and speed on the interfaces? The ios is 6.3(3)Thanks
I have a pix 501 that I have recently upgraded the version to 6.2(2). I have tried to upgrade the PDM to the same version (currently 1.1(2)) however I get an error saying not enough flash memory.Show flash retirns the following....pixfirewall# sh fla...
I have a Pix sitting behind an ISDN router We have a /30 pubic address range. One IP is ssigned to the dialer interface and the other is a static NAT for the mail server. The router is doing NAT to a private range that the Pix sits in. When we try to...
Hi all,I've got a PIX (version 6.2 (2) ) and it happens one thing I don't understand. This PIX have got 4 interfaces (outside, inside, DMZ and another one).In the inside zone there's some servers with private ip addresses. Users from the inside and ...
Hi, I know that this question is about inside Cisco information, but I am just curious if there are any plans to use the USB connector on Cisco PIX platforms (especially for the 501 and 506).As some of you know, I'm from the Netherlands. In our count...
Hello,my PIX is the Default Gateway for my LAN.Can I configure a static route in my PIX 5151E to route packets from my LAN to another gateway in the same LAN?Thank you in advance
I have one pix 525 with eight interfaces, six fastethernet and two gb-ethernet. I can setup the interface gb-ethernet1 how the internal interface wiht security levell 100.
We are validating our sw vpn users on our 3030 via nt domain. Therefore there are no individual userids.How can we selectively disable certain users? e.g. A few office workers not allowed to come in from home.If this were Windows / RAS we could unche...
I have a VoIP gateway that is marking packets with DiffServ CS1 and CS2 levels. These packets first hit an internal router that has a GRE/IPSec transport mode tunnel to another router on the public Internet. The internal router uses its FastEtherne...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-16-2025 04:21 AM | ||
07-06-2025 01:40 PM | ||
07-04-2025 01:59 AM | ||
06-19-2025 07:32 AM | ||
06-17-2025 01:07 PM |
User | Count |
---|---|
11 | |
6 | |
4 | |
3 | |
1 |