Network Security

Hello,Is it possible to force a failover switch between PIX-515 firewalls by using SNMP (MIB variable)? The two firewalls are configured for LAN-based failover. Beside the normal failover switching criterias, we are looking for a solution to initiate...

106012: Deny IP from 192.168.1.1 to x.x.x.x, IP options: "0x14". I receive this syslog message about 6000 times per hour from our Pix. This is from SAP frontend clients logging on and sending packets to SAP R/3 servers. Does anyone have any idea or d...

Dear Sir,I am looking for the PIX Firewall Configuration Guide Ver 6.2 from the following link:http://www.cisco.com/en/US/products/sw/secursw/ps2120/products_configuration_guide_book09186a00800eb49b.htmlEvery topic under above link brings me to the s...

Hi all,I have a bunch of PIX 506E's acting as a FW's for a VPN I have deployed. We have a Nortel Contivity client sitting behind it doing Nat Traversal connecting back to a Nortel 4500 Head end at Corp. The problem is that all other sites work except...

Does anyone have some advice on how to configure MRTG to monitor a VPN 3030 concentrator? I'm interested in graphic bandwidth utilization on the public and private interfaces, as well as active connections, IPSec flow, and CPU utilization. I've tried...

Hello Could you please help.I was testing pix 501 for the first time. Upgraded it to 6.21.I got it configured and after booting it, it lost its eth 1 interface. Now it does not come up at all. I would say that interface is broken, but we werHere isCi...

I have had conflicting reports and no success with enabling Network Extension Mode between these 2 devices. One consultant said that it was impossible to impliment, one said it was not even configurable with the firmware available, but Cisco says it ...

Is there any known interoperability issues between CIsco PIX-525 firewall and the Interlink software's RAD-E server for Solaris ?. We want to authenticate the users cross the firewall using RADIUS protocol and the RADIUS server should run on Solaris ...

We are looking at implementing a cisco pix in stages and therefore want to stick clients behind the firewall first then servers. Is there a way to do this for the domain loggin in without putting a PDC behind the firewall with them? I am able to have...

I'm looking to configure a PIX (v6.2) to accept connections from various IPSec VPN clients which will be connection from dynamily assigned IP addresses (no way to predict ranges). The clients will be anything from xDSL routers to dialup clients. (In ...

I am trying a hub & spoke vpn, but all the www traffic is out the main site. All other locations do not have a split tunnel at their sites. The access lists for nat are created but if an extended ping is started out one of the remote sites it will no...

Dear all,In RME3.4, the storage option stated the default max. messages kept is 1000000 and days for message to keep is 7 days. Does any one know how can I associate these two values. Does it mean syslog messages older thatn 7 days will be deleted? B...

question one:cw2k can't display gauges at localhost,the java applet dispaly 'Not able to connect with the server".But it works fine while i open 1741 port at another pc,a new problem came out is if I push the refresh button, a "Access Control Error: ...

I am planning to use lan-based failover on PIX, but am wondering if it really works well or not. If anyone has the experience with this technology, please let me know how the implementation goes.Thanks.

Trying to VPN into work thru my home PIX running 6.2.2 code to work PIX running 6.0.1 code. I am currently using the 3000 client v3.6.1. At home, I am running cable so I do only have 1 outside addy (which is dynamic).What I did notice is that the hom...