Network Security

helloCustomer Purchased CSPM 2.3.3i with license Cisco Secure Policy Manager v2.3.3 (unrestricted) License Disk, to manage IDS sensor.he wants to install Client/server configuration,installation of server works greatbut when he try to install client ...

HiI have configured FTP on PIX and it is working well,Now I want to configure SFTP on PIX 515 with ver 5.3(2),is this ver supports SFTP protocol,if yes How is it configured.ThanksNamdev

I am attempting to connect 50 remote sites to our main office PIX 515E using PIX 501s at the remote sites. I have two sites up and working fine. When I issue the command SHOW CRYPTO ENGINE is see: Crypto Engine Connection Map: size = 8, free = 4, use...

PIX 501--- I have hosts (6) of them right off the inside interface, I got one host that has an ip of 192.168.30.10 I want this host to be able to reach the outside i.e. internet. I also have clients on the outside who access the 192.168.30.10 via Cis...

Dear Sirs,we`re using Cisco Secure PIX Firewall Version 5.2(8), and we neeed to configure multiple PAT.we try to put it with the command global (outside) 1 x.y.z.a netmask 255.255.255.0 for the first statement and global (outside) 1 a.c.d.e netmask 2...

We have a PIX 535 configured in Failover with 6.1 version. After pasting a large acl (about 20-30 lines) into the PIX, it reboots. I request to know if any one has faced a similar problem?Rgds,vamsi

We just purchased a PIX 515 - no floppy disk. I know the procedure to perform the password recovery i.e. using tftp method but have no idea what the internal ip address is in order to execute the monitor > . Any other options/solution?Thanks.. Jacky

Hi!How can make FXP work through a PIX 501 6.2?FTP works fine. I`ve open port 2849 tcp and udp but it still wont work.I´ve been told to open a range of ports. How do I do that?access-list 102 permit tcp any any eq ftpaccess-list 102 permit tcp any an...

HelpI am following the documentation but having difficulty getting the pix to authenticate with the Microsoftg ca server.My debug message is:CRYPTO_PKI: WARNING: A certificate chain could not be constructed while selecting certificate statusWhat does...

I'm trying to use CSPM 3.0 for managing a PIX 515 with three interfaces and 4 VPNs terminated on it. I have already configured the PIX with CLI and works fine, but I just acquired CSPM3.0 and want to use it for management. The problem is that after I...

the outside ip address of my PIX is dynamicly assigned from my provider DHCP server.is there a way to define and inbound acl to allow inbound traffic to go thru with port redirection.my problem is that if my outside dynamic address change from 64.1.1...

Will this work, you need 32mb for for 6.2 image. Whats the deal..? Can upi up the mem. for the 501.. Anyone know ?thanks!

I am trying to connect a PIX 501 to our ISP (Cable service). I am unable to get a DHCP address fro the ISP, but DHCP works fine on a WIndows network (I plug the PIX into a port on the private network and I get an address from the Win2K DHCP server w...

I have 2 PIX 520's setup with failover between the 2. If you unplug an interface that is in a switch or hub this will cause failover between the two... Failovers kill connections. I need to move the connections into a new switch without causing a fai...

Does the PIX support BW Management ??? If Yes how you configure it via CLI ???