Hello everyoneI have a weird problem with configuring SSL inspection In Cisco FTD , every time I enable SSL policy In ACP all ssh session that go through FTD will be drop after 10 to 20 seconds .even configuring all SSL Rule to do not decrypt still...
Forum Posts
Hi All, Im trying to reach ip (10.100.20.66) hosted on cloud but not able to achieve it. Attach is the Error im getting if i do packet-tracer. Below is my packet-tracer command. Can anyone help me to resolve this issue packet-tracer input inside tcp...
Hi Folks, I have a situation where I need to change my standby firewalls MGMT interface IP via Primary one.My secondary is up but not reachable for SSH due to service providers IP conflict.1. Is it possible to do so ? or shall I need to arrange an en...
Has the inability to assign multiple certificates to a single IDP been addressed in a newer version of software yet. We are on ASA 9.12(4). The Bug report says it is fixed in certain release, but the numbering makes no sense as to which release it is...
Hi Please I need support for my SCCM server, I have a problem between the SCCM and the Cisco firewall ASA 5540 I have windows server 2008 R2 Slandered I enabled Hyperv and I install SCCM as virtual ok my Active Directory is windows 2008 R2 and SCC...
I have an ASA5506-X that has been reimaged with the FTD 6.2.3.17 image. It is configured to be managed by a FMC running 6.6.5 which is the last version that will manage 6.2x devices. I have Base, Threat, Malware & URL filtering licenses assigned to...
Hello! We have an scenario where after initial configuration and registration, an FTD will be complety isolated without contact. Besides the NGFW capabilities due the lack of updates, what other features will get disable? Is there a document detailin...
Hello, Fairly new to ASA, have done some limited work in the past. Wondering if someone could give me a quick run down on what the following ACL statements do and, following the last statement, is it implicit "deny"? access-list outside-acl; 4 eleme...
Hi, I have a strange problem with a Firepower 1010 device that crashed after upgrading to 7.1 (Beta release)After booting, I now see the following errorNov 21 10:01:16 firepower FPRM: <<%FPRM-2-UNSUPPORTED>> [F1326][critical][unsupported][sys/switch-...
Hi, Is snmp supported for FTDs in Azure ? cannot find any documentation saying that it is not. I am not able to make it work.Management ip is replying back on port 161 to snmp server but it is not working.
Resolved! How to Block Youtube Whit Firepower?
Hello All I have this scenario can't Block YOUTUBE.and how doing block per network or users I try but don't work this form best regard. Sebastian. ,
Resolved! Issue selecting Tunnel Source
Hello, I have updated FMC and FTD to version 7.0.1 (build 84) and since then I have noticed that when creating a tunnel VTI the tunnel source does not provide all available interfaces. For example, in one of the cases I want to select outside interfa...
We seem to be having an issue to correctly configure rule within our access control policy using the FMC for our FTDs. If we need users to be able to access any url link that contains .azure.net on ports 80,443,3389,1433, is the proper way to configu...
Hi,I am using Cisco Firepower2110 with Virtual FMC 6.3.2 version.I am facing an attached error while deploying policies. Could you please guide how can I resolve it.
Resolved! Restore a FMC backup on FDM
Hi,Today I have a Firepower FTD that are managed by a FMC. I want to set up another FTD, but with local FDM management, running the exact same configuration as the other FTD. Would it be possible to take a FMC config or device backup and then restor...
