So this is a LAN setup & using GUI but can also use cli if needed.Ive been troubleshooting this for a few days and I think FTD is blocking the access between the port 3 and port 1.Here´s the setup: Host - 192.168.3.5/24FTD Port 3 - routed status - 19...
Hi, Is there a way to filter logging output to a specific interface on the Cisco ASA ASDM? I have tried the ASDM Logging Filter under Monitoring->Logging->Real Time Log Viewer However with this tool you can only define limited parameters like "Source...
HI, I am using ASA5516-FPWR-K9 firewall since 7 or 8 months. I used to run "Updates" from ASDM and update worked fine. Last week I run the same process but it returned following error...Error: Download Updates Failed: Peer certificate cannot be authe...
i want to have a setup where ASDM users have a second factor before having access to the firewall. kindly assist if anyone has done anything similar.
Hello,I have switched configured with 802.1x to run as authenticator.In one of the ports I would like to add Cisco ASA as supplicant and keep 802.1x enabled.So the question is , can I add a username and password on the ASA so it will authenticate its...
Hello All, I have a customer who wants to stay on the ASA platform but needs to support more throughput. I thought about ASA on Firewpower. I could install the ASA software on a 2110 for 2.3 Gbps of throughput or a 2140 for 9 Gbps of throughput. I...
I'm a bit frustrated. I spent probably 30 minutes looking for a replacement on Google, and I saw lots of references to the ASA-5512-X and 5515-X, but end of life isn't too far out. I then chatted with Cisco for nearly 25 minutes and was getting trans...
With Cisco AnyConnect client 4.6, the embedded browser is used for login when a SAML IdP at ASA is configured. For previous versions on AnyConnect, there was an option of using the system native browser (configured via the command saml external-brows...
Hi, we applied the FTD update version 6.4.0.10-2 to patch the recent Cisco vulnerability and after it was done, I went back into the updates just to verify they were all applied. To our surprise, both FTD appliances, are still on version 6.4.0.9-62 e...
Hi, anyone here experience to access their ASA firewall (ASDM/SSH) from the inside interface but the user is coming from outside interface of the ASA? I see some use cases using management-access but it uses VPN tunnel, can it be done without using a...
Hi Is there a way of exporting the syslog settings (syslog id, syslog level and enabled/disabled) from ASA to FTD?I'm looking at a daunting task with plenty of hours of manual labor if not. /T
Hi all. I'm new to the ASA devices. I have an ASA5512 plugged into a business router trying to get VPN access to a secondary network. I cant seem to get the anyconnect web launch to be found. is what i'm trying to do even possible. The last time I se...
Okay so I have an old SG 200P. It was installed years ago and there are is no knowledge of credentials and no known config file. Here is what I have:1. SG 200P that will power on and LED lights on ports when things are plugged in BUT no SYSTEM LE...
Hi,I have been trying to figure out if I need to upgrade my ASA firmware version, but the more I read the more confusing it starts to get.I have two ASA active/standby firewall pairs - A pair of 5525-x and a pair of 5506-x The 5506x are running ASA v...
Hello guys,I am going to upgrade Anyconnect client software on FTD using FMC.My question is when the anyconnect client software is uploaded, what happens?- Is anyconnect client software on user side going to be upgraded automatically?- Should user go...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 09-28-2025 08:37 PM | ||
| 09-26-2025 12:33 AM | ||
| 09-24-2025 06:11 PM | ||
| 09-23-2025 04:54 AM | ||
| 08-29-2025 08:17 AM |
| User | Count |
|---|---|
| 11 | |
| 5 | |
| 2 | |
| 1 | |
| 1 |
