Hi everyone, I saw this thread from 2019:https://community.cisco.com/t5/network-security/vti-on-ftd/td-p/3923610 regarding the VT Interfaces on FTD. Sadly I can't find any resource that confirms or denies that this implementation is possible. I have ...
Hello guys, im totally confused i need to understand something. so i have done wired user and machine authentication using eap chaining, why is it that when i remove anyconnect from the pc i am not able to authenticate either user or machine ?
Dear all,I have problem with SIP phones which are registered with their public IP on CUCM instead of private address assigned to AnyConnect client. (AnyConnect client for android v4.9, ASA with firepower module v9.8(4)) Now, SIP clients are successfu...
I'm in the process starting my first round of ASA to FTD device migrations and have concerns and questions regarding what to do with management interface on both during or for migration purposes.My current ASA is attached to Firepower Management Cent...
Hi,we are Using Firepower 1100-Series as ASA for VPN with AnyConnect.When A user loggs on to the Webinterface to download the AnyConnect Client there is a button on the lower right corner to show step by step Instructions to Install the client for th...
Hello Guys,can you help in the belowThere are no harddisks in my ASA 5585-X with FirePOWER SSP-60 . if i make IOS upgrade from rommon modeand i make a reboot it goes to rommon mode again . when i checked i found that the flash option (copy tftp flash...
Hello Guys, i really need support . i need to buy a HDD for cisco ASA 5585-X with FirePOWER SSP-60 , but i don't know if i need to buy a cisco HDD or some other vendor will work .is there any comparability matrix for the HDD that can be used with AS...
Hi Community, Cisco released note for FTD 6.3 has not officially included posture in this version, would this create an issue with future support assuming we successfully implement posture? Regards,
Hello Guys,I am setting up a cisco asa 5505 FW. I can get interent on the FW and i can connect to the vpn client fine and get a address from the vpn pool i created. The only issue is that i cannot reach the inside interface from the VPN pool. Can som...
Hello,we have cisco asa 5510 (asa version 9.0(3)) and we have purchase a cisco firepower 2130 (with image asa, no FTD).Is it possible to migrate the configuration currently present on a cisco asa 5510 direct to a cisco firepower 2130 with image asa ?...
Hi all, A couple of questions around configuring ASA on Firepower 2130, especially around port-channel and SSH access to ASA.I've followed this guide to configure both FXOS and ASA, but direct ssh access to ASA via management interface is still faili...
HiI have two Firepoewer 2110 in an active/standby model,In official times, it's NPU usage is between 80%-95%, after that it reduces to 40%this is the result of usage:> show cpu coreCore 5 sec 1 min 5 minCore 0 81.2% 79.8% 80.7%Core 1 80.6% 79.4% 80.4...
I got this issue on Cisco ASA. I do not have experience with it. Could you please let me know what I should do to fix ithere is some information# show failover stateState Last Failure Reason Date/TimeThis host - SecondaryActive Ifc Failure 09:31:20 ...
We have just deployed our FMC/FTD on 6.6.1 and have A10 sending our logs to Elastic. We have the logs going to the server via UDP but would like to use TLS per our requirements. I know I need certs from a CA and those certs must be the signed by the ...
Hi team,i m setting up multiple vlan in firepower and vlan are seperated to two interfaces, one interface connect to Nexus switch and one interface connect to Catalyst switch, FW interfaces are trunk mode to each switch. ACL are already allowed betwe...
