hello to to everyone, as i am new in firepower 1140 device, i would to like to configure a static nat to the inside interface 192.168.1.1 translated to the public ip which is the outside interface through a pppoe connection (running vesion6.6.0).the ...
Hello All, I was setting up ldap-attribute mapping for having multiple group policies within one tunnel-group. But when i test the connection it fails to select any group-policy and fails since no IP address is being assigned. The ldap-map is:-----ci...
I bought an ASA 5520 from a local for sales and the seller said it had the botnet filter and GTP/GPRS included. The ad also said it would be reset to factory defaults. Upon startup, I was presented with the ROMMON prompt. His version of factory defau...
Im trying to run asdm.jnlp but Iced Tea crashes after a bit: net.sourceforge.jnlp.LaunchException: Fatal: Launch Error: Could not launch JNLP file. The application has not been initialized, for more information execute javaws/browser from the comman...
duplicate entry hence deleting it
We have ASA running 8.2.It has NAT 0 for Cisco VPN users below nat(inside) 0 access_list Zero_NAT----------1 When I config new NAT 0 for IPSEC belownat(inside) 0 access_list Exempt_NAT---------2 When I put NAT config line 2 it overwrites the NAT 0 ...
Hello, Im just attempting to configure and add two 2100s to FMC. under the local-mgmt cli I have applied an IP address and I can ping FMC, however under the FTD cli ive added the manager (FMC) but am unable to route there. looking at the interfaces u...
Hello,After upgrading from Rel 03.08.E to rel 3.11 [c4500] we are experiencing issues with IP device tracking where after IP Device Tracking Probe Interval experienced [now in rel 3.11 300 sec, before 30 sec] no IP ARP probe requests/responses are se...
Hey,I don't get the followingnat (outside,dmz) source static any any destination static 1.1.1.2 2.2.2.1 unidirectional no-proxy-arp1) Why does the ASA respond using Proxy ARP for the global address? (The asa's own interface is 1.1.1.1/24)2) ASDM warn...
Hello, I have ASA 5555-X with FirePOWER which I didn't use yet. I downloaded two images for it, then asasfr-sys and ftd. I assume that the appliance comes with the asasfr preinstalled and one must reimage it with ftd if FirePOWER services is needed. ...
When I enter into rommon mode to upload an image, the link is down on my interface to set up the TFTP. However, I have configured this port for no shutdown. When in enabled mode, the link is up with no further configuration. Is there a way to make th...
Hi, I'm running an FMCv version 6.2.3, have been for a while and everything seems to work fine. However if I try and configure the database event values and click save I get an error saying "The Host that you are trying to configure (x.x.x.x) could n...
Hello everyone, I am facing a strange issue that'why I hope someone here will give me a solution, at least a good lead. I have a new customer that called me because he had his VPN KO : anyconnect profile didn't work.I saw that there was a HA configur...
Just wanted to find an answer if virtual KVM FTD v 6.6.90 supports tagged (dot1q) pakets pass though inline interfaces.With untagged vlan 1 no issues all works perfect.But tagged vlan 100 packet is NOT passing though the FTDv.Any knows an answer, if...
We're using Cisco ASAv 9.10 together witch Cisco Anyconnect 4.7 clients. Due to the Poodle voulnerability and other vulnerabilities I'm doing some changes in CBC ciphers, and we're turning off TLS 1/1.1, plus changing from Diffie-Hellman group2 to gr...
